Search results

I thought I'd pass this along. I'm in the market for some but asking price here is beyond what i'm willing to pay. Buick Grand National,Regal,T-Type,Turbo T,Rear GM Bumper Fillers Happy Bidding.

..use a air impact on the old bolts to get them out. I did the DS UCA and was able to access the nuts for the frame bolts from the engine side coming in from the top. Plenty of room. Got the arm off without having to remove the steering shaft. The PS is a different animal. Can barely access...

Need to replace these and the GM Part# 22017846 is coming up discontinued. I'm sure I could find a old pair used but wondering if there is any charge left in them by now. Mine are fully collapsed and won't extend back out. TIA

Looking for a pair of tranny oil cooler lines for a 200c transmission for a non-turbo 3.8L engine. Original factory bends must be there and no other bends, brakes or cuts. TIA

Since I'm getting the transmission done I'd like to replace the lines while it's out. Can only find the ones for a 2004R though. Will they work for a NA Regal w/200C trans? Thanks.

Installed a new crossmember the other day and while doing so I had the transmission on a transmission jack for support. I had to "bump" it up some to get the new mount for the transmission installed. Now the column shifter won't go into park. It still thinks it's in reverse. Did I tweak...

I specifically told the place I brought this crossmember from I needed one for a 200c metric transmission and they told me all the crossmembers are the same for out cars. Well after sand blasting and re-coating the damn thing I finally got around to dropping the old one today. They are not the...

There is a small serrated washer on the UCA pivot shaft. Not the big retaining washer on the Outside, this one is on the inside before the bushing goes on. I've searced everywhere but can't find a replacement except if you buy a shaft kit which I Don't need. Does ne1 know where they can be...

I'm rebuilding my Front CA's and need the serrated washers that go on the shaft before the bushing. There's one on each arm.

Does ne1 know how to remove the bumper/stop from the Front Upper CA? Not the bushing on the Pivot Arm. Thanx Morbid

Well I finally finished project I started changing the Front LCA's w/new bushings, Springs, Shocks, Stabilizer Bar Bushings and End Links. I did the DS earlier this Summer and finished the PS today but looking again at the DS LCA it looks like the spring shifted and the bottom of the coil is...

Some time ago a mechanic replaced my speedo cable w/a aftermarket one. Ever since then fluid leaks from where the cable goes into the transmission. Is there a gasket or O-ring that goes in there? Second leak is in the rear of the Transmission where the prop shaft goes in. Again is there a seal...

I needed to replace the mount for the crossmember on the DS. I got the kit from GBody Parts and for the life of me I can't get all the holes to line so I can thread the bolts. I've tried both with the member jacked up and not. I've tried using an alignment punch and pry bar's but no love...

I replaced all three e-brake cables today using ACDelco parts but the Drivers Rear Cable isn't long enough to reach the connector w/the front cable. I replaced the equalizer (bracket) as well. Is there some trick to this? The cables are routed the same way the old ones came out. The rear...

I was able to successfully install the Rear Feed Brake Line with the help of a fellow board member. Replaced the hose that goes from that line to the rear axle while I was at it. So far so good. I'm working with pre bent SS lines from Classic Tubes (I brought the complete Brake kit) and...

I need to replace the E-Brake Cable running along the underbody on the DS. The one that snapped runs from a connector located about under the DS Door to the Equalizer Plate in the back where the Rear Cables come in. It's called a intermediate cable and I can get it special order (no returns)...

The E-Brake pedeal is stuck all the way down to the floor how can I get it free. The FSM shows 4 cables for the E-Brake. Front, Center/Intermediate, and Left/Right Rear. However I can only find Front and Rear Cables to buy. Did they discontinue making the Center Cable and the Front Cable now...

Finally got around to installing the bushing in the LCA's. First order Rock Auto sent me didn't have all the parts in the box. Second order all four bushing were in the box and thankfully installing the bushings was way less pain and suffering than removing the 20+ year old ones. However I'm...

I know at least one of these, the dual one for the brake/fuel is messed up already. Would like to get some replacements to have.

For some reason the FSM only has one spacer for the tool to install/remove the bushings from the lca. It's too short for one side. By the time I got the bushing out I noticed the the flanges are bent inwards. At least on the outside one. Is there a fix for this or is the arm toast?