Search results

Drivers power window quit so I go to parts u pull it and got one out of an 85 regal for $12 and it worked fine. Actually faster than my "start rolling window up two miles from home" motor. Get it in and drive 1 mile only to realize the passenger one would not go up and it was burned out. Go back...

I'm planning on taking this the GoodGuys on March 14th to sell. Need to pay off some things so it's time. Figured I'd let people on this site know. I'm asking $17,500 and have a lot of extra buick stuff to go with it. You can see most mods in my signature, which is a lot. I have 3 sets of...

My dual fans quit and I think they are the ones from Ramchargers. When I put juice to them I hear the relays on the fans click (the two blue connectors on the fans). I do remember smelling something like an electrical fire not too long before my temp started climbing. Could they both burn out...

Got an external pump from alky control to replace my in-tank pump on my SMC Alky. The red and black wire seem pretty simple, hook to the black and red on new pump. I have two white wires on the pump that I thought he said were to control a selenoid. My two white wires come from in my tank and...

Have a set of BNIB GNX Center Caps, never installed. Bought these off of a member but they are about an 1/8 too big for my wheels. Mine are a smaller Kirban aftermarket center cap. There is a one plastic tab that is broken off of two of them. I think one was missing and the other broke in...

Is there anyone who could replace my pump on my dual spray smc alky kit. I'm assuming it went, but haven't confirmed it. I have a power light but I hit the test button and doesn't bog down or change idle at all. Could I replace the pump my self with something that could handle methanol? Is...

I"m waiting on a response from racetronix but figured I'd see what I could find out here. I have a diy hotwire that I'm replacing so I can get my fuel pump issues narrowed down. Do I run this kit through the firewall and the interior back to the trunk or can I just run it outside along the...

I have the denso pump for the twin turbo supra. When fuel pressure gets to 45 pounds it drops off and of course start to get knock so I get out of the throttle. I had another denso pump that I put it and it does the same. When I put the second pump in I noticed that the wire going to the...

I have the denso pump and as you can see the fuel filter is folded almost to a 90 degree angle. I had to do some special rigging to get the denso pump on the hanger. The filter must have been hitting the baffle in the tank. When I try to go full throttle the fuel pressure goes to about 40 or 45...

I have a fairly new denso pump and it has been working great. I just started getting knock so I put the fuel pressure gauge back on. I hit about 45 to 48 pounds and then the pressure falls off and the knock goes up. The last time this happened the fuel line inside the tank split. Is anyone...

Where can you find some sort of decals for the GNX wheel center caps. You can get the center caps at Kirbans but they don't have any type of decal anymore. THese are for the wheels that have a 3" center hole. I need at least two. Or four center caps with decals.

Has anyone bought the metal overlay piece for the upper part of dash to replace the plastic piece that cracks. This is the part with the speaker grid and defrost openings. Seems like a cheaper, maybe better solution, but just want to make sure it looks decent.

Just got motor back in after a new piston. Fired up and you could hear lifters a little and they quieted, then looked at auto meter electrical oil pressure gauge and it didn't move. I might have ran it 10 seconds. I did prime oil pump with drill in cam sensor and the drill bogged down and felt...

Just wanted to make sure there is no washer of any kind on the bolt holding the balancer to the crank.

I need the plastic piece that goes around the back of the engine and comes up toward the alternator that all the wires travel through. I'm sure it has a name. It would be shipped to Texas 75501

I have done some searching to find out the torque specs. The gntype.org I believe says 40, the arp website says from 45 to 55 (the part number I have doesn't match, and on one of the threads someone said 75#s. The number on the head of the rod bolt id 2000, these are stock rods. I think I...

Had to get a new piston so I'm doing rings. The piston is a sealed power forged piston. The rings the builder (not the original guy) ordered were sealed power E 434K 30. My block is .30 over. When I search I don't get a lot of answers for ring gap and the ones I do get are different. I checked...

This is the block out of my car from several years ago. It is a .40 over Jasper rebuild, so the crank wasn't the right one. I bought a standard block for my rebuild. I also have a crank that I bought that is .10 over and .20 over that I did not use. These have been in a shed but the moisture has...

Here are some pictures of what happened when the alky wasn't spraying and burnt the electrode off of the spark plug off of number one. Number two lost a little piece and left a couple nicks on piston number two. Is this a good time to get some champion heads? Will This block have to be torn...

I will be pulling my motor (totally ate my spark plug in number one). Looking at my signature what would you recommend for an upgrade without serious money. What I want to eliminate is the annoying ticking sound that will come and go. Sounds like a lifter. On last rebuild I took apart every...