Search results

Would anyone know what I need to do to just run the dash lights fuel level and headlights and signal lights etc by them selves. I will be doing a ls swap and was hoping to retain stock stuff

Would anyone know what I need to do to just run the dash lights fuel level and headlights and signal lights etc by them selves. I will be doing a ls swap and was hoping to retain stock stuff

Hey guys thinking off doing a v8 turbo swap been waiting along time for the turbo 6 to be built, I will leave it at that, I was wondering what I need to keep the original dash working with dash lights does anything work off the original c437 connector or for function off the original dash (don’t...

Hey guys thinking off doing a v8 turbo swap been waiting along time for the turbo 6 to be built, I will leave it at that, I was wondering what I need to keep the original dash working with dash lights does anything work off the original c437 connector or for function off the original dash (don’t...

Has anyone ever run a 1\2 fill on the 109, in a mostly street driven engine with a adequate cooling system. This would be for a weekend warrior by no means a daily car. Just looking for opinions. Thanks

Hey fellas just inquiring about which T\C I should run. I just ran an Art and Carr 9 3500 NON Lock unit in my old setup. which I believe ballooned and ended up taking out my thrust and main bearings and also did some fatal damage to my trans aswell.:( 2004R I am just wondering which brand...

Hey there just purchased a set of Weld RTS rims. I needed a set of lug nuts and purchased a set of mcgard 1/2 inch 20 RH thread with a .75 shank from the local speed shop.. these seem to be flush with the back of the rim with the washer in place. My question is, I know now that they are supposed...

Hey guys kinda got a 2 part question here. 1st part has anyone had any experience running the universal FAST XFI harness and if so how difficult was it to install and does any one a double pumper with it? 2ND does anybody know if their is a way to remove and rewire a pin connection inside the...

Have done my utmost to label all connections before removing the entire harness but have missed a couple just wondering what connection this connector goes too....? Iam stumped IMG_20150701_120037 by Vandal1987 posted Jul 1, 2015 at 6:53 PM IMG_20150701_120023 by Vandal1987 posted Jul 1, 2015...

Would anybody know where the Fuel pump relays grey wire originally plugged into. I think mine dislodged when I was pulling the harness out... . And also what is its purpose? and would it have any effect on a double pumper hotwire kit from working properly?... Thanks !!

Just wondering does a hotwire kit from Racetronix eliminate the need for the original fuel pump relay that was in the engine compartment. thanks in advance.

Hey there guys I am in the midst of swapping over to FAST XFI and want to run a stand alone harness using my stock unit. I was just seeking some insight as to what connections I can totally delete from the equation. Just wanted to double check with some more knowledgeable folks before doing...

Hey all was wondering about some creative ways to stiffen and strengthen the frame without putting a cage in. So far I am going to be re doing the body mounts and replacing them with new poly ones. I am also going to be ordering the gns frame brace kit. I will be running an H&R setup aswell. Are...

Hey there guys just had a query into the amount of Wheel Horse Power a forged crank, rods and girdled 109 can safely withstand before the block itself becomes the weak link in the chain. If we are to say the motor is tuned safely and professionally also the block being assembled a very competent...

Hey guys was doing some work on GN the other day and when I was under the car I noticed a couple bubbles on the passenger rear fender and with furtherer investigation found some loose rusty metal under the wheel well and then discovered another couple spots....:mad::eek: mind you this car has...

Hey guys just in the midst of replacing my motor I suspect bearings are finished after the motor was removed and TC taken off I noticted this on the input shaft is this bad? the trans was still working before the motor busted.. ..... Looks like a piece is missing and if so how much to replace it??

Anybody know how to find out weather you have a set of Champion Irons ie , A stamped number or something that differentiate there heads from other aftermarket manufactures.?

Hey guys, I just picked up new motor and I am in the process of getting a FAST XFI system from hartline performance. They have requested that I supply them with the Cubic Inch size of my motor, The motor in question is a 109 stock block with 40 over diamond pistons and a stock crank. Would this...

Hey there I recently bought a racetronix duel fuel pump and have hooked up all the lines and other hardware but now I am kinda stumped on the electrical side of the installing of the double pumper. I was wondering how to hook up the wiring harness to the alternator. The kit's wires came...

hey there was just wondering how to make the alky come on sooner in the psi range any one know how to increase this adjustment via Razors Alky kit I don't have instructions for kit :(.