Search results

I have a lot of parts from an 87 GN to sell. I was going to swap the motor into another car but I have since lost intrest. No luck selling everything together so here's everything broken up a little more. $2000 takes - Block w/ rotating assembly - Heads - Lifters and push rods -...

I have a large selection of parts from a GN I parted out. The drivetrain is complete. I also have front and back seats, carpet, center console, dash, and cluster. Every plug in the harness was labled and only one wire was cut. I would like to sell everything toghter.

I'm looking for a te44 or a stock turbo. Nothing worn out or in need of a rebuild. Thanks.

Took the car for a short drive around the block after sitting for a long time today. It didn't seem to be building boost so I pulled the intake hose off to check the turbo. No movement. I pulled off the oil feed hose on top of turbo and it was bone dry. Argh, it seems likes there is an oil...

Don't miss this chance to get 650 ft/lbs of torque at the wheels for only 450$. I would get it but I'm saving up for the $8,500 GNX. :cool: http://cgi.ebay.com/ebaymotors/grand-national-3-8-turbo-t-type-84-to-87-intercooled_W0QQcmdZViewItemQQcategoryZ33615QQitemZ8042456861QQrdZ1

This winter I installed a trans+ and extender chip. With the chip in the car will start up and the die after about 3 seconds. The car does not have this problem with the stock chip. I think the problem is fuel pressure. The instructions say to set fuel pressure at 45psi and I don't have an...

I'm looking for stock regulator I can attempt to modify or a good used regulator, and a fuel pressure guage. Thanks

I found a map sensor in a box of stuff that came with my car. Can anybody tell me anything about it from the numbers on it. TIA On the side that the hose plugs in: PBT-GF30 9576-24 Back side of the conector: C B...

I am faced with a choice and I'm not sure which way to go. I have an 87GN that has major rust issues and I'm thinking about doing an drivetrain swap. I went by the base jumk yard and they had a 79 GrandPrix and a 74 240z. They had just arrived and had not been picked through at all. Both are...

I just downloaded TurboMeter and built a cable. I was wondering if I should get any readings when the car in not running. I was thinking I would at least get a TPS reading or maby the P/N switch. I had the key in the "On" position but I didn't start it. Does the car have to be running for it...

I just finished rebuilding my trans. and I noticed the new filter has some rust on it. I went to the base auto part store and they quoted me $40 and 6 weeks for it to get here. Bum deal. I don't want to wait to have one shipped from the states so I was wondering if any Opel's were ever made...

My car came with TurboLink v2.13 and a dead laptop. I have a working laptop with XP. I'm think about upgrading to v4.0 but the cost is $170. Yet I can buy the CD w/ v4.0 for $6. Are the v4.0 cables better or something? Can I just buy the new CD and keep my old cable? TIA If I could...

When I removed the forward clutch pack I did not find anything that looked like a waved plate (part # 666 in the atsg book). Does the bfr not have these plates? Should I just use regular steels in place of the waved plates? Does any body have a picture of one a waved plate so I can go back...

Hey, I broke the electrictal connector for my TCC. The middel part w/out wires that run through the case. Does anybody have a part #? Thanks

Last week I pulled the trans in my gn and noticed the BF R tag in pretty pink. :) I've only had the car about 2 months and it has had a pretty rough life. With all of the horror stories about people sending a BFR to aamco (or like place) and having it lost in the rebuild, I was still weary...

I leaned up aginst this and broke it when I was working on my car. Oops. It is located next to the mastor cylinder for the brakes (converted to vacume). Can anybody tell me what it is so that I can replace it. Thanks.

Second gear went out so I'm going to be rebuilding my trans. I have read some people say that they have a tendancy to destroy the TC also. I really don't want to replace the stock one because of the $$$ factor. What is everybody's take on this? Can I just flush it out really good or...

I'm going to pull my trans. tomorrow so I'll need to tow the car home. My plan was to pull it home with some rope but I can't think of any place to tie off too. Does anybody have any tips on how to do this with out destroying the ic shroud? I only need to pull it about a mile.

I'm about to rebuild my trans and I was wondering if i could set it on the oil pan when as i take it out of the car. The shop (a pay to use type garage on base) I'm going to be working at has a tall jack with a square about 2'x2' on top. Just balance or strap it to this base the lower it down...

I took the cover off my heater core box today, it's supposta be filled with water right? I'm thinking no. Is (52479871) the correct part number? I got the number from gmpartsdirect.com but I can not find the part for sale anywhere with that number. I have also looked on the potson site...