Search results

I recently relocated to the area and would like to know of any reputable machine shops with turbo Buick experience. Will likely need to have the crank turned and mains aligned bored and bore/hone cylinders. I have searched and found some older posts on the subject, but nothing relatively...

I am looking in to replacing my rods and I have seen 3 different brands that sell them and they are all 3 different lengths. Full throttle speed sells 2 of them. The CAT h beam rods are 5.965 in length, and the K1 h beam rods are 5.960 in length. I also found a set of scat rods that are 5.970...

I spun the no.6 rod bearing on my 86 T-Type. It is the orignal engine and has 90,xxx miles on it. I want to rebuild the bottom end on it but need some ideas. The car will not be driven very much and for the most part it is basically stock. I am going to budget for around $2500 for the...

I have purchased an adapter from Moates to install a 27sf512 chip into my ecu and I am trying to burn a program onto this chip with no sucess. The program that I am trying to burn onto the 27sf512 is a program I took off of a 2732a chip. I am using a moates flash and burn and the errors I get...

I have purchased an adapter to install a 27sf512 chip into my ecu and I am trying to burn a program onto this chip with no sucess. The program that I am trying to burn onto the 27sf512 is a program I took out of 2732a. I am using a moates flash and burn and the errors I get are: chip start...

I have a custom chip that has a scanmaster fast update rate and I was wandering if there was a way to datalog with Tuner Pro in the same speed as the scanmaster. If I look at the values on my scanmaster, they update about 3 times faster than the values on Tuner Pro. How can I make them match...

Any one ever built one and have any instuctions for it?

I am wanting to learn to properly tune my 86 T-Type via factory ecu. I have a few questions I can't seem to find the answers to. What all is need to get started datalogging? I am ordering an adapter for the ecm so that I can use the newer reflashable eproms. I already have a Burn1 chipburner...

Any one going this Friday 6/10 for the annual cruise?

Does any one know where I can get the PC board to build my WB O2 project? I e-mailed the person who was selling them on the web site ( http://jubjub.mine.nu/wbparts.html ) a few times but I have gotten no response. Thanks

Has any one used these chips in their TR with the adapter Moates sells? How well do they work? Thanks

My old alcohol pump is no longer working as my car sat for a few years and it locked up. It is a Bosch pump from an F150 I bought 5 or 6 years ago. Back when I put this kit together, this was the most common pump to use but now it seems ther are more choices out there. I have a 2.5gal alcohol...

Any one know where I can get some info on where exactly to place the different emblems on my 86 t-type. I tried gnttype.org but they only had the GN, not the t-type.

What do yall use to keep the canter caps on 86-87 T-Type wheels from falling off? I've tried super glue but they still come loose. Mabye silicone? I can't afford to keep buying new ones.

I am looking for the clips that hold the blacked-out windshield trim to the body, the ones that run up the a-pillars and across the roof line. The one on the left (white) is the original one that came off the car. The one on the right (black) is the one I ordered with a part# I got off another...

I need to know what eprom i need to buy to run in the stock ecm of an 86 t-type. I am planning to burn my own chips but I didn't know what kind to use. Thanks

After hours and hours of trying to get my seals to actually "seal" I have finally accepted the fact that they are going to leak. They seal up ok for the first ten minutes of water testing but after that, they start to puddle up in each of the front outer corners where that little depression...

I am looking for a flange that mounts to the exhaust housing of the stock turbo so I can attempt to make my own 3" downpipe. Does any one know where I could find one? Thanks

I did a search but couldn't find anything. What would be the best paint to use on the outside metal edge of the t-tops, the part just above where the seal actually goes? The original black has faded from the weather exposure so it would have to be somewhat weather resistant. Thanks

Do they need to be replaced when replacing the cam?