Search results

I solved the problem with no start. removed cam sensor, the gear pin was broken. replace with new cam sensor, set up the sensor, started on first twist of the key. i has luck with gear staying on shaft when removing the old sensor. thanks for all the help.

Thanks I will check.

So far the cam sensor window is not turning when cranking the motor over. Removed window to look over the tab, not broken. This week end will pull cam sensor out and hope cam sensor gears are not chew up, also check pins in dist gear. Next step may require to remove front timing chain cover to...

Thanks, I have a feeling new cam may have eaten the cam sensor gear

full battery charge, motor does not really turn over that fast. New timing chain installed less than 2000 miles ago. While I'm in the area, I can look into the timing chain condition. Car just stop running one day, no back fire or and signs of motor going bad. it acted like someone pull out the...

Wheel w wheel was not turning while cranking motor over. Can i get away with just replacing new wheel and new cap instead of complete cam sensor assembly. thanks TurboBuRick.

THANK, i will try tonight....

i'm back on the GN that die, it is the same old story, no start. Measuring voltage at B5, i'm getting 2.5 volts with switch on and will bounce around a little when cranking. New crank sensor installed and set up. Also new plug at crank sensor and wiring. NEW coil and ECM and ignition module...

what is the moser part number ??? thanks

t-top If you have after market t-tops, i would think that a after market t-top company ( installer ), could look at your set up and see what brand they are and help you out. There are a few after market company in my area that deal with all types of car add on's. good luck

builder Shawn: Kids are getting bigger !!!! I really do not know Ivan, Do you have his phone number or address. I'm looking into rebuilding my trans. down the road. Thanks

t-tops Are you talking about the weather stripping that goes on the T-top, held down with two screws ?? You need to make them as long as you can stretch them out ( slots ) to fill up the gap. I just did my last month, help alittle. I did get my off of E-bay ( GM ) I hope this will help.

part numbers What part numbers for booster and check valve and master cylinder for a vacuum conversion should i ask for at Pep boys or ??? Thanks

I had the same problem, installed a momentary switch on the ground wiring going to the gauge. After starting engine, just push in the button for a second, gauge will reset. I put my switch next to the gauge in the gauge pod.

the steering column ignition is cover by the guard, only reason i got the guard to cover the key opening. Paul

2 cent worth I had the same problem for a while, could not figure it out, every thing was right on. I was running on 5 cylinder, checked my ECM and found that one wire had worked loose in the plug that fired the injector. You could not see it by looking at it, just started the car and pull on...

guard Kirban has a column pro-gard steering collar lock for $50.00. works very easy, and will stop the common a#$ h)@es from breaking the window and using a common screw driver to drive your car away.

co2 kits Just starting to get into the co2 world. I have a DEI air intake kit ready to install and play with ( tuning ) I did also get a cheap intercooler spray kit off E-bay, still waiting for the kit. Being in sunny Florida, inlet air temperatures are very high ( 100-145F ) thinking about...

same problem I had the same problem with batteries, had to carry a spare one, so i could get home. I checked for shorts, still batteries die. Change out to a 200 amp alternator kit and got a OPTIMA red top battery. it has been in the car for three months and NO dead battery. My car is a...

co2 systems Try some of these people: www.intercoolertechniques.com www.nitrousexpress.com www.speednosis.com I just got today DEI cryogenic air intake system. It is very well made but a little pricey. Looking to build my own system for intercooler and air intake, should be fun to...