Search results

Anyone going to hit the temple or Little River strip tonight. I went last night and a couple weekends ago. Last night was dead, but maybe everyon is waiting for tonight. The tech guy did say something about a buick shoot out next weekend.

Anyone around the killeen area that can lend a Catalytic Converter or sell one. I need to get the Texas Saftey inspection, and they are being anal.

The part is attached under the master cylinder that provides pressure to the rear brakes. Pump motor does run. Half of reservoir empties with in a day and a half. Leaks directly below unit on the A arm to the ground.Brakes real hard, so Im guessing I only have front brakes. Light does come...

When you have your voltmeter hooked to the blue wire coming from the cam sensor cap (key on, using no jumper wire) what should the voltage read? Mine reads 4.93.

Finally got the car hooked to a computer. These are the problems that where noted. 1) No EGR Vac (even when he closed manually there was no change in motor) 2) idle ignition at 38 (car also has a very high rpm at low speeds) 3)TPS fluctuates just a little with gradule increase of rpm 4)...

I have a Direct scan 1.52 with cable and a Shorty style 3 inch stainless Test Pipe. Will sell for $200 or trade for Scan Master.

I finally got my car running and drove it down the road. I dont trust it to venture out too far. I put new piston rings in and through diagnosis replaces a ton of unnessary sensors. It idles around 1200. I dont hear any misses. This issues that Im having: 1} I brought up to 5 lbs boost...

Quick question. I found the exact same car as mine with 177,000 miles on the origional motor, the same modifications, same rusted through rocker panels, needs paint and has under carrage rust and to top it off it does not run and I dont know what is wrong with it. What is this car worth...

11/32 7 DEG MACH STEEL LOCS in the box paid $32 K-Motion Valvue Springs in the box paid $ 123 1.265'' Dia. Single H-11 Valve Springs, Seat Load: 130lbs @ 1.700'' Open Load: 395lbs @ 1.150'' Coil Bind: 1.050'' Max Lift: .610'' Set of 12 571-K-750 T&D 1.65 Shaft Mounted Roller...

Just put the motor back together. Started in up and made alot of noise in the heads on both sides. Pulled the breather off and the noise matched the rocker arms movement. I just pulled a valve cover and I dont see a drop of oil in them. How is this possible?

Just put motor back together after a piston ring replacement. Now no white smoke, no engine blow by, starts right up. I only replaced the piston rings some misc gaskets and valve stems. Now it sounds like there is alot of noise in the heads. Any Idea what it could be, or is everything just...

It will turn over and sometimes try to start, but then it stops and make a weird like back pedel sound or like you try to start a car thats already started. I guess I need a diagram for the block and coilpack. I wired it up a different way according to a post on here, but it immediately...

4) 1987 Buick Grand National with alot of miles but am currently doing complete engine overhal. I have over 11k invested. Not your average daily driver, most likely for car enthusist or speed freaks. Many, many, many extras. I also have a complete short block build and ready for delivery. I...

Sorry so long, but I need help and I copied for my thread from another area. Hopefully someone here can help. I have been fighting these issues for a long time with no resolve. No smoke at startup or idle. Light very faint white smoke if I give it gas. More smoke of course under boost. Not...

someone please come help me with my 87 GN, before I have to sell it. My number is 5733372070.

I have to sell my girl. I have had her for about 6 years I guess, but now going through the big D. I cant quiet get it runnig right. It starts right up, idles fine. Has a good vibration when your sitting inside. No smoke at idle, if there is its to lite to see. Give it some gas, then I see...

Had the car in government storage for 17 months. They did start it up and move it once a week. Ever since I got it home it has been running crap. I dont have my scan tool, but I have been using a voltmeter to set the TPS/IAC. The car will not stay running unless I give it gas. Has a weird...

Max Effort 16 Pos w two chips for 83s for $175 or trade just the ME for Direct scan or scanmaster. 3 inch stainless shortey straight pipe for cat elimination. $65 Free Steel GN hood with hail dents. Pick up only also looking for someone to buy a running 109 short block will all...

I am selling the virgin short block with 77k miles on it and 4 passes. This includes the oil pan, D roller chain, crank, pistons, stock intake, heads with 100lb springs and new retainers and a custom ground cam (sorry no cam card), but I can vouch it is at least a high ten second cam. This...

GN Metal Hood (needs paint and has hail marks) $50 pickup only Testpipe 3" Stainless $50+ship stock doghouse (tb included, but levers are missing) $25+ship 83 lb Seimens injectors with ME-16 and chip $400+ship