Search results

Billet vacuum block sitting here (with vacuum brake tap and milled lines on top). I removed 2 of the 5 PS ports and replaced them with setscrew/epoxy since I didn't need all of em. The gasket is included. $15 (should handle shipping and my hassle going to the PO). For some reason this could...

Well, I've been getting a lil bored with the same ol stuff on this forum so I figured I'd add a possible interest area: I've started work a system that has an actual active feedback loop which I surprisingly haven't seen in a system yet! I'm using an industrial stainless pressure transducer...

I'm still trying to figure out wtf was going through Accel's programmers brains when they created their awesome TAU/MAP table. If the ECM only looks at a difference between cells, then why didn't they just put some delta paramter there instead. No, but now you have to freaking adjust a whole...

I knew a few ppl were interested in some WG pucks so I got a few from Keith. They are 1.5" diam. $25 each shipped. spoolinup@gmail.com Thanks! Phil

Stock turbo oil drain - no leaks, good cond: $35 shipped Fitting for above (block fitting): $5 if with above or $10 shipped email: spoolinup@gmail.com Thanks! Phil

10 bolt 8.5" POSI Rear drum to drum. Rebuilt ~10k miles ago with new clutches and heavier springs. Also replaced upper bushings (rubber). $900 I also have a billet vacuum block sitting here (with vacuum brake tap and milled lines on top). I removed 2 of the 5 PS ports and replaced them...

I found these really cool thermocouple meters that do datalogging both internally and via. RS-232 to a PC. I am putting together a package and am seeing who would be interested. I am shooting for 10+ units. Here's the package: EL Backlighting: Here’s the PC Datalogging...

Super quick shipping and very helpful folks... Have had several perfect transactions and they are very nice and friendly - even when some minor order changes arise. Phil

As title says, where can you get these two plugs? Nobody's got em! Phil

Well it's done and as promised here are some good pix... LCD bezel is finished, console is done, speaker & door panels finished and loaded. I've also modified a RR skin with a layout that I could more easily use and like. This handles all of the media... movies, DVD, internet, radio, MP3s, and...

For a high tolerance engine, it is desired to get the most oil flow possible, no? So what spring should be used? How is the oil flow affected as pressure goes up? From what I recall, the oil is bypassed via that spring and plunger, therefore, should I just put in the heaviest spring if my oil...

Here's a progress posting for my touchscreen and carpc install... http://www.turbobuick.com/forums/showthread.php?p=1311803#post1311803

Here's what I've got done sofar to my interior... The carPC i'm using is actually an old P3 machine that I retrofitted and isomounted into my own casing. The touchscreen is an 8" Xenarc unit and fits quite nicely into the stock radio/CC area, much to my surprise. I use the...

I am getting pissed here... I've done this 3 times over the past 3 years now, and the liner has fallen again, yesterday in the heat. I have used new material, a perfectly cleaned foam backing, 3 different 3M adhesives: super 77, 76, and high strength (90 i thinK?). All of them have failed when...

I figured I'd post my results sofar with my HFT cam install as many ppl have been doubting HFT cam installs RE: wiping. Cam is big, springs are 150 seat 320 open. Well, sofar so good. I have the heavy springs in there now and it runs fine and no signs of wipe-age. I did breakin with...

Does anyone have any nice pics of some fiberglass doors for these cars? I would really appreciate it as would, im sure, many others as there is no good source for images of them. I am particularly interested in the internal and hinge area. Thanks! Phil

Well, I've been fooling with this alky stuff for quite some time now and have been trying to find the "right" pump without having to get one specially made or paying over 600$ (e.i. Weldon :) ) per unit. I have been using Shurflos since I started the system and have only had some small...

1. Billet Vacuum Block with brake tap, modified to remove 2 of the hoses on the 5 port side... I didn't like all the lines going up there so I plugged 2 of them. $20 shipped 2. IAC with Angle Boss Adapter, like new... $30 shipped All include gaskets and hardware. If you want both...

Has anyone had a car shipped to them for a pretty far distance? I'm looking at a potential Supra that fits my "checks/needs" very well and there are none around here that are cars im interested in... that has been checked for the past 2 months across the country... So I got a quote to ship...

Well we all had some fun at the dyno today... hehehe Here's the car: Side View (just looks like a good ol BBody wagon right?) Here's the highest we pushed: Best Run Here's the engine bay: Engine Wagon This is a completely stock LT1 block with 112K and Keith's TT setup he's...