Search results

There are some "REAL" pro GN professionals on these boards. They know the engines and electronics inside and out. There are also some products that come out that are great and have some issues before they are perfected. That is the way life works folks. Please do your research and don't judge a...

I am very happy with the Bailey's 2 step. The consistency of the RPM is well worth it. The brake peddle install was perfectly instructed and I will save the 200r4 because there is no need for a trans-brake. Thank you Turbo Bob and to the community as a whole for steering me toward a solution of...

I plan to run 275/60 R15s so I'm kind of expecting a u-joint issue if I do decide to compete at all with the B3 folks. Just purchased. LIMITED LIFETIME REPLACEMENT Part # 234 from Advance which states it is a perfect fit for my 87. If someone breaks one before I do, hit me up as I will have it...

I ordered the 1 from Cotton's but also wondered if anyone had ever used this 1? I plan to do the job with the heads on and was wondering if this tool would work? I know I will probably have to use the 1 from Cotton's on number 6 as it is in a very tight location but this one here looks like it...

First year going but raised in Hendersonville, TN 1 hour away. Anyway, I actually had this ready to post in another thread but this event seems pretty special to most everyone here so I just started a thread about my first time. At some point, all of you were here? Correct? Well, this story...

I will be at the GS Nationals early Thursday morning 10-25-2019. I have all the tools. If you "KNOW WHAT YOU ARE DOING" with Comp Cam 280-12 valve spring installs and can perform the install in a reasonable ammount of time for me to test and tune, I need you there.. I have 24 keepers, valves...

Thanks

Any info on bump boxes and what is involved in installing an electronic trans-brake? You can save the gay jokes for the GS Nationals on the 23rd -26th.... :)

I'm sure this has been answered by Bob or someone that is an expert in PL but I don't see any thread for this. I don't yet have any analog inputs occupied on the analog interface for power logger. Should the power logger installed in the ECM be reading boost levels; as this is an all stock car...

Pigeon Forge Fall Rod Run Sep 12, 2019 - Sep 14, 2019 (865) 687-3976 Pigeon Forge - Tennessee, 37863 This event will be located at the LeConte Center in Pigeon Forge. Please call 865-687-3976 for more information I'm told that the TR folks generally meet up at the Cracker Barrell...

So one would think that going from 2 Bar MAP to 3 Bar Map would cause the factory gauge to show less than actual boost. Not the case with this one.. I T'd the vac/boost line to an external gauge and left the factory gauge as is. Now the factory gauge shows boost just above idle and max boost...

I just completed the PL install. Not sure if this is stated anywhere else but the simple answer is the metal things on all corners of the 2 boards are NOT rivets.... The boards are stuck to the metal brackets that form the structure because they have been on there for 30+ years. Use a very fine...

So. I have a question about additives.. Oil and Fuel... I added some Lucas 3X boost and filled up with 93 octane to hypothetically bring the octane up to 96.8. I also added 4 oz. of MMO to fuel to lube up the upper cylinder walls. At the same time, I added 28 oz. to the oil to clean up the...

I am looking for a shop near the Nashville, Tn area to go thru my car with me and tell me what the build is. Also, EricM, I will be back home June 1 and will get the numbers off the 5.7 chip to see if you know any background on the build. I would imagine it will get very expensive to have a tech...

Hello all. Bought an 87GN. Looking for the previous owner. Charles I Waller of Middletown, Ohio. Car was sold to Metcalf restoration and resold to Maple Motors here in Hendersonville, TN which is where I found her at. It has the paperwork and chip 5.7 from Turbotweaks (Eric) I would assume. So...