Search results

:mad: Ok, I tried the cam sensor at several positions just a few degrees before & after the setting listed on GNTTYPE & I still get the same results. I've heard of some type of a theft code that can get set in the computer & possible keep the car from starting. How can I check for it or...

I'm trying to finish a nearly four year long project with my 87 GN. Got the motor in and everythings hooled up now, but I have had everything (dash included) out of the car & gutted at one time or another. I had the short block assembled by a local machine shop, but I index the cam and...

Looking for a set of good condition fuel lines for our cars.

Finally got the motor in and everything bolted up & wiring ran. I tried to start it and it seemed to fire a couple of times but wouldn't run. Kind of seemed to fight itself. I set the cam sensor according to gnttype.org but its not real clear on the instrustions. When adjusting the window...

I've got a booster plate I was going to put on my car. I've replaced the front cover with a H.V. one. I would like to use the plate instead of having the gears spin against the aluminum bottom part of the pump. Last time I installed I couldn't get it to stop leaking. The instructions say to...

Match ported my intake & had a good port job done on my heads. I want to use the 1200's but what are you suppost to do about the valley?? I've got about 1/8" between the bottom of the intake and the block valley where the pan would usually seal. This will get pressurized under boost won't it...

I ordered a set of TRW's & rings new off someone on ebay. The rings were in their original box but the machine shop is telling me that both #1 & 2 rings should have a chamfer on them where my #2 ring is flat. Anyone every ran accross this, did they change their style, and are these any count...

Does anyone know how to get ahold of Ramchargers. Their website won't come up for me. They were the best priced for the new HV front covers with HV oil pump.

I've got a used 218/218 from Precision. Its been kept in good sahpe and only had ~ 2K miles on it when taken out. I've got all the lifters from the cam ordered in sequence. I was gonna use it with new lifter, been in the box & passed hands so the lifter kind of worried me. This is a new...

Trying to balance my rotating assembly and I can't find my flexplate. Where can I buy a new one or does anybody have an old one. THANKS

I was wondering what cylinders run leaner comparitively to the rest. I'm doing my machine work right now & it turned out that one rod was .015 shorter than the rest. Considering two possibilities, 1~ different rod & index them all the same, or 2~ run the short rod on the #6 cylinder to assist...

Has anyone had any problems runnig higher compression in these motors ~ 9 to 1. I'm taking my stuff to the machine shop this week and I'm gonna try something a little different. Also is the exact standard bore & stroke on these 3.80 & 3.4 or where can you find these specs. THANKS Jeremy

Can you get the cable for the P.C. to the ECM anywhere else besides when you order Direct Scan. Does anyone have an extra?? How much & where can I get it?? What else besides the software do I need to hook up? THANKS Jeremy

Trying to find a good set of aftermarket rods IE Eagle H beams but can't find anyone. I'd prefer not to have to spend $1000. How good are the stock rods? Looking at mid tens.

Can't find a machine shop around Louisville KY that has a torque plate or is know for Buick work??

Who sells these?? Can't find them on any ones website.

Need one good al brake drum and an alternator core. I have a good alt but the housing is cracked. a burnt one or lock up makes no difference. THANKS Jeremy

Looking for a headliner in good shape or the best place to get one. I don't have the back board either so I need everything. THANKS

Trying to do a resto project. I bought a factory replacement Driver side header and cross over from ATR. They are both nice SS pieces. I can't find a passenger side header to bolt up to the factory cross over. ATR doesn't sell one and I don't know where else to look. Any info would help.