Search results

incase anyone's interested: http://www.turbobuick.com/forums/parts-sale/288885-complete-87-engine-transmission-rx7-swap-kit.html this is mark (gnx7) 's old setup. with my engine/tranny.

My t-type was rear ended a few years back, i pulled the engine and transmission in hopes of doing a hybrid swap. bought all the swap components off another member who parted out his running hybrid (gnx7). Since then i tinkered a little with the engine, but between picking up 1.5 more degrees...

thinking of selling my lt1 rx7. could use some extra $ for a bike or engagement ring. some info: 95 lt1 out of an F body recently refreshed, and good compression. granny's swap kit. t56 6 speed, with a spec stage II or II+ clutch. it also has brand new delrin (solid) bushings all around...

so i broke the T-bolt for the v band clamp for my ATR headers (for crossover pipe). The pipe is 2.25" OD and the flange is 3" OD. Most (all i've seen) V-band assemblies labeled for 2.25" tubing, use flange OD's smaller that 3". and I think I have to use a clamp labeled for 2.5" tubing in...

I have an old set of stock heads, valves, springs, pushrods, lifters etc. moving out and gotta clean out the garage this weekend come and get them or they're going to the dump. located in glenn dale MD. vince1@gmail.com

I put in a roller cam kit about a year ago. bolted up the stock rocker arms to see where i was at preload wise. preload was off so i was going to order pushrods or adjustable roller rockers. since then I got tied up with a new project and the engine has been sitting with rocker arms bolted...

one weld repair, inside ground smooth. Worked perfectly after repair. 200 OBO + ship. please email at vince1@gmail.com as i don't check the boards that regularly anymore. I also have a gutted cat that went on this (goes to 4 bolt flange) if the buyer wants as well. thanks.

009 injectors with extender chip. 100 shipped. vince1@gmail.com

009 42.5# injectors with extender chip: 300 OBO please email vince1@gmail.com if interested.

4 AR torque thrust II's 17"x8", 5x4.75" bolt pattern The wheels are alittle dirty in the picture, they could use a good polish. Tires are Ventus HRII 245/45-R17 with decent tread left. pics attached. asking 700 OBO. email: vince1@gmail.com located in Maryland

I haven't run the direct scan for awhile but last night i made some runs with the DS and i noticed my MAF readings at WOT jump all over the place (and with them my injector PW #'s). I was wondering if this is a normal with the trans +, or should i be expecting a smooth MAF reading. the MAF...

I recently replaced my TA60 with a new GT6152. I had to change one of the wastegate solenoid hoses because of the different location of the compressor pressure outlet. I hooked up the "Y" fitting correctly with the restriction towards the compressor outlet. i'm still getting 25+ psi of boost...

I just blew my TA60. I have been looking through the threads and am thinking of going with a TE-60. i was looking for some opinions on some of the other turbos that are comparable with the TE-60, 61 or 62. i am running 009 injectors, 3000 stall converter and alcohol shooting for a turbo with...

I just bought a used trans + and 3.5" LS1 MAF from a buddy of mine. I installed the MAF and trans +, and tried to run the car before I hooked up the two spark wires in order to make sure the MAF was working alright. The car ran terribly and would hardly rev up or hold idle, when i was able to...

I been trying to order a 1LE brake conversion kit from him for awhile now but i haven't been able to get in contact with him. I was just wondering if anyone on the board has been able to contact him recently.

when i brake hard i can hear a clunk noise coming from the passenger side (pretty sure it's coming from the front pass side), and when i release i hear another clunk. It seems as if something is popping out of place when i brake hard and pops back into place when i release. It seems to only...

I havent driven my car for about 6 weeks. now the right turn signal will not always blink like it is supose to. when i go to turn on the turn signal, the dash indicator as well as the turn signals will just light but not blink. also when my headlights are on, the right turn indicator on dash is...

what are the torque specs for the tranny fluid pan for the 200 4R? thanks.

this might be a dumb question but how are you guys able to tell when your transmission is shifting at WOT. My stock LED tach just lights all the way up when i go WOT. i've tried to use the scanmaster to read rpm but it's too slow to get a good rpm measurement. the only thing i can think of is...

what repair manuals do you guys recomend? I have the chilton's guide, but I need something a lot more specific. How good are the factory manuals from Helm? Thanks.