Search results

Here's my craigslist post. http://cincinnati.craigslist.org/cto/5536482140.html. Should tell you what you need to know. If interested let me know via text. $17,500 Thanks, Marty

I have a set of new headers made by Headman headers. As I was told, they were made years ago as a special run for the SE Buick club. These look to be very much like the old Poston headers only with better welds. I bought these a couple of years ago and never used them. Took the pieces out of the...

Ok I have the correct NTK O2 sensor. I got the O2 program from FAST. I have the lambda sybol which is suppose to tell you that the computer and the sensor recogize each other. What I don't have is a working O2 sensor. My Uegos V off the dashboard view reads 4.6v with ignition on and about...

Just installed a classic fast system. Didn't look like the O2 sensor was working. I bought the system used. Bought a Bosch uego with a NTK connector. Read that it was a cheaper replacement. Tried it last night and no readings again. I heard from someone that I needed a disc to set the WB...

I have a Modded ECM for low impedence injectors. $200 plus shipping.

I have a barely used Scanmaster for sale. Works great, not a mark on it. $215 shiped to lower 48

I'm trying to replace a cracked balancer off of my 4.1 motor. I got a replacement balancer and have now discovered that it is not the same as the one off my car. Difference being that my cracked one has a reluctor ring and the replacement is aparently a pre-reluctor ring balancer. I guess the...

Like the title says. I am looking for a harmonic balancer for a 4.1 motor. Who can help me out?

Can someone tell me how or who can remove a reluctor ring and replace it onto another balancer? Would a machine shop do that? Anybody know somebody in the Cincinnati area? Any help would be greatly appreciated. Thanks, Marty

I have what i believe is a starshifter for sale. It has the 200r4 cable on it, i was going to use it on my regal but never did. Now that i dont have the regal, i dont need the shifter. Ill take $50 shipped. Im in fairfield, OH Josh

I'm looking for someone to tune my Gn in the Cincinnati area. The car has a TE63 turbo and 83# injectors. It should be running low 11's to mid 10's. My Gn recently burned up its ECM and needs to be checked for ohm draw off the computer and possible wire harness shorts. Can someone help me...

I'm looking for inside storage for my Gn and GS. I live in the Cincinnati OH. area. I am willing to pay a reasonable price for safe inside storage. Let me know if you have something or know of a good place. If the spot was warm enough to work on the cars when it gets real cold that would be...

Help! my car wont spool to more than 4 psi, and it doesnt do that until 4k rpm. My theory is a clogged cat, because around this time, the small leak in my crossover got waaay bigger. I dont have a wastegate solenoid on the car, but its set to 16-18 psi via wastegate actuator arm. What else...

Hey all, been busy with work and school and let the old thread go away. I've got the car dependable now, had a bad fuel leak but reaplaced the line with braided stainless steel. Took care of the popping at high rpms, go figure! Well, car has unknown miles, but engine has about 3000, and tranny...

I had a moddified ECM burn up. Bruce said:The best answer, would be taking an ohm meter, and going thur the outputs to make sure one wasn't too low, and overloading the ecm. Can someone tell me what the ohm outputs should be for low impedience injectors? (#83 r's). I don't know enough...

Looking for a modded ECM for 83# injectors. Please help. Marty

I have recently converted my car over to 83# injectors. The ECM was modded for the injectors. Ran the car down the track a couple of times and discovered that I needed a new wastegate salenoid. Got that in and took car for a leasure ride. Got about 5 miles from my house and ECM burned up...

Hey all, ive got my car up for sale, im just not ready to have that kind of power, so here it is, all the work was done by Patrick Smith (sixgun86gn) my dad or myself. Motor work was done a few thousand miles ago, have the receipt for it but im not clear as to what was actually done. Anyways...

Hey all, ive got my car up for sale, im just not ready to have that kind of power, so here it is, all the work was done by Patrick Smith (sixgun86gn) my dad or myself. Motor work was done a few thousand miles ago, have the receipt for it but im not clear as to what was actually done. Anyways...

Just as it says. Crossmember off a Monte carlo in good to excellent condition. The mount is new. $40 plus shipping. Thanks