Search results

I have a relatively stock block that has been sitting on an engine stand for the past 5 years. I kept oil in the motor and all that. I am going to do minor work to it like a cam and replace the valve springs, injectors, headers, turbo and all the sensors, wiring and high output distributor. Do I...

I was wondering how to get the heater box out of my car. It looks like I have to take the fender off of the car along with the inner fender. I wasnt sure if there was some way to get it out w/o removing the fenders. Any help will do, thanks guys! Brendan

I was looking into installing a 12pt. cage into my '86 GN. I currently have the dual A-pillar gagues on the car now. Is that something I will have to remove due to the bar coming down the A-pillar or can I still be able to see them? The other question is who has the best cage out there. I am...

I found a bracket in my trunk that looks familiar but I am not so sure as to where it goes. I think it came from under the hood on the front drivers side fender well. I am not too sure though. Any help would be appreciated. Thank you!

I have a mech fuel pressure gauge that I purchased for my car. What is the easiest way to hook the line up? Can I tie it in to the Oil Feed line for the turbo or is there and easier or better way on doin this? Any help would be appreciated. thanks guys!

I am installing a new electrical auto meter water temp gauge into my car. Can I tap right into the water temp sensor on the front of the engine or will that not work? Thanks in advance

I just was wondering if anyone sells 4" MAF hoses for my MAF pipe. If at all possible it would be nice if they were blue but anything would help at this point. Thanks ahead of time!

I am going to have my car buffed in about a week. I would like to remove the Grand National badges along with the 3.8 SFI badge off of the hood. How would I do these safely without harming the paint? I heard a heat gun works but to be careful but I wasnt sure if there was a safer way to do it...

I am going to bow my rear control arms myself. I was wondering if anyone sold just the bushing (hi-perf.) for these. Thanks Brendan

Gas Gauge Not Working I just got around to hooking up my battery the other night after having the car in storage for the past 1.5 years. I noticed that my gas gauge is not registering. I took my gas tank down and looked at the float and the wiring and everything seemed in tact as far as I know...

I was just wondering how the 2" Supspension drop would affect my performance. I am more concerned about performance than dropping it but I have seen a few that were lowered one and two inches and they looked nice but didnt really know how this affects 1/4 mile time. ANy input would help. Thanks...

What is the best way to hook up a mechanical oil pressure gauge to my GN? I am clueless! ANy help will do, thanks guys Brendan

This might be a stupid question but what is the correct hose to put on the Y Fitting where the orfice is located? Thanks guys Brendan

I just received my translator plus and I am hooking it up to an AC Delco 3" MAF. I dont know where to connect the White and Black wires for the timing part of the Translator. Any help would be appreciated Brendan

What are the best shock I can buy that can be used on my GN for the street? How about the best adjustable ones for the track? ANy information will help - no hurry. Thanks guys Brendan

Can anyone give me any tips on how to remove the wire harness from the engine compartment with the engine still in the car and heater box? I am not sure if I have to remove the heater box to get the one loom out or if there is an easier way. I am also stuck on the d.s. fenderwall, how can I...

Does anyone know where I can buy the most recent version of the turbo link software. Thanks Brendan

I was wondering where I could purchase the MAF translator plus? If anyone could help me that would be great. Thanks Brendan Q

I purchased my 86 GN about a year and a half ago from a guy in WI. There are two wires coming out of my passenger side kick panel that he said had to do with the factory alarm system. One wire is solid green and the other one is Blue with a black stripe. They are both cut and he had them tied...

I know that aluminum pipes are better to use on your air intakes since they cool down quicker but what about if you powdercoat them? Aluminum tends to get dull after about a year and I hate polishing aluminum so i thought that powdercoating it would solve the problem of polishing. Just...