Search results

off of my 87'T - I had the dutt neck ported,spring cleaned,installed and painted in Jan'12. Ic has no leaks the Stock scoop comes with it all work and condition can be verified by Bweavy I went to a bigger Ic now. $175 shipped to U..paypal ...aaclark38@hotmail.com if anyone's interested.thnks

Just wondering which Cam I can go with my setup te-44, ptc 2800 stall, dutt intercooler, rjc power plate,60lb inj and matching tt chip,lt1 maf -translator. I don't want to bother the heads other than replacing the valve springs and lifters just want to bump up from stock since I have to put a...

Last Aug i bought 60lb inj and TT chip combo 93 oct, then it was a basically a stock car.Since then I have added a te-44, rjc power plate,lt1 maf and translator, ptc 2800 stall,dutt neck stock intercooler,8' k@n filter as of now and planning to add a 3' dp and pypes race pro 2.5 exhaust cat-...

I have a brand new kirbans 3'down pipe For sale New out of the box with clamps also a reman caspers cam tool brand new also ..Changed my plans $ 190.00 shipped..Thanks

Got a new te-44 and a kirbans 3'down pipe vs. A $450 down pipe ?? Will the kirbans work just trying to save some $$.Thanks /

are bilstein shock part # front 24009492 and rear # 24009294 that everyone uses on there TB's..

could someone give me a part # for a transmission cooler Im upgrading to a te-44 and a ptc 2800 stall converter i just want to be sure to have the right 1 when i buy,,thanks for any help :confused:

A kirbans 3' down pipe...atr or thdp

What size are the bolts i need to bolt up a set of front frame braces for the under side of the car like kirbans sale # 6564..Thanks

Terry Houston Down pipe or ATR Down pipe must be 3 inch..Thanks

I have 6 stock injector's and a hypertec chip for $30 shipped I upgraded to 60 lbs and matching tt chip. Paypal aaclark@dreyers.com Injector's and chip are not Brand new..Thanks

I'm planning on installing a 2800 lock up stall converter soon what's the best Brand to buy ?? And also as far as a trans-cooler does it need to be a Heavy duty unit ?? All PM's are Welcome Thank's to All :cool:

How do I install a new crank sensor and cam sensor on a 1987 turbo-t im still a novice to these Regal's .And what is a cam tooled used for ???? Thanks :frown:

Today while at a red light my shut off like i turned the key off ,Upon arriving home I parked for about 10 min came back out and now the car will only turn-over with no sign's of firing all my scanmaster reading's were normal after the stall,fuel pressure with key in on position was 40 psi and...

Dutt neck and steering column lock...in good condition Thank's

My car is breaking up when going into boost I recently installed a 60 lb/injector/chip combo 92 octane,New walbro fp,Caspers hot wire, Ac delco IAC, translator with lt1 maf, 8'k@n filter I took all these readings at idle and normal driving temp.. 02milivolts = Lowest 320 #'s jumping around...

looking to buy a 2.1 scanmaster must be in good condition..Thanks

Im installing a new water pump on my 87' while it's off ima go ahead a change out the timing chain are there any more parts I need ???? I'm ordering Comp cam #3129 timing set, fel-pro timing cover gaskets cork, upper-lower hoses ,,,,, Thank's ;)

These are a 275/60/15 they were mounted on my car less than 20 mins way to wide and I dont want to roll my fender.1 tire does have little fender nicks around the edges due to being wider. Thank's $ 325.00 shipped It might take me a bit to respond due to the way I work if anyones interested.

I just upgraded to a LT1 maf and translator also a billet fpr.The Mech set the fuel pressure at 38 psi after leaving the shop the car shut off at the stop sign just like it did before the upgrade. Do I need to take the fuel pressure to 43 psi ?? I'm still running the stock chip, I do have 60 lb...