Search results

Hi Brad Could you point me in the right direction to who has this Delphi MAF unit. I can't seem to locate it online. Thanks

Hi Brad Does your unit Delpi or is it Delphi work ok with the Maf translator? The 25180303 are a bit expensive so I am interested in some alternatives.

Just for education purposes why does the Maf have to be 25180303?

Hi Brad The BLM'S go from 128 to about 131. I have changed my intake system to 3 inch from the K & N filter to the MAF. From the Maf to the throttle body is still stock with the little piece connected to the oil tube. Should this piece be upgraded to 3 inch? Randy

O2 SENSOR READINGS ARE ALL OVER THE PLACE. LOOKS FINE THEN DIVES TO ALMOST ZERO. I HAVE REPLACED THE O2 SENSOR AND SAME PROBLEM. I HAVE CHECKED THE IAC AND CLEANED IT.I HAVE REPLACED THE MAF WITH A SPARE 87 UNIT. i HAVE A LT1 MAF I WAS USING WITH THE MAF TRANSLATOR BUT STARTED GETTING 33 AND 34...

Hi Adrian I have the 295-55-15 on the El Camino using a Weld Prostar 15 x 8 with 4.5 inch backspacing..There is still a 1 inch clearance from the frame but not much room on the body side. Randy

I have replaced the O2 sensor today. The readings after a while go above 700 to the 800 range. Everything seems fine then there is a stumbling and the readings head south to below 100. This is all at idle.What can be the matter? I need help.:confused:

This is my stock wastegate unit. We just threaded it to make it adjustable. If I recall my boost was about 5 lbs. I might have the boost gauge in the wrong spot. I have it t-d in the line that branches to the boost unit on driver's side. How do you test if the wastegate is shot?If its shot it...

Cat has been off for ages. upgraded turbo and added the adjustable wastegate over the winter. Ecm upgrade a couple of years ago. Could it be a bad wastegate controller?

Hoses. wastgate , what should I be checking?

Was at the track for the first time Friday. Pathetic times, no power on top end. Had 5 lbs. boost first time. Adjusted waste gate rod as short as possible and got to 10lbs. and no more. Checked hoses from dual waste gate controller and seemed ok. I have my boost gauge inline( t-d)with the hose...

I am being lazy, but car is parked elsewhere and I have to haul my tools over. Does anyone know what size socket the knock sensor takes. I am going to try removing it and reinstalling like Brad suggested. Thanks:biggrin:

Another question comes to mind. Has anyone upgraded to an electric water pump?

Go buy the shifter, the instructions will guide you throught the process. Everything you need will be in there. The shifter cable is far superior and the conversion takes a while but the results are rewarding. Do a search in the forums like I did to keep the linkage to move your gear selector...

Thanks Brad, can you move closer to Calgary...lol. I will consider electric in near future. If I go electric how do you hook up the positive, ie: what source, fuse block, or do you put a switch in? What kind of electric pump should I use?

My fan clutch is showing some wear and tear. The seal was gone and the bearings were showing. At the time I was not sure what replacement to get from my parts supplier. Is it important to get a thermal or non-thermal unit? I got and have installed a Hayden part #2707. Not much info but looks...

Many thanks for the info.

I have had knock issues before and usually from low octane fuel. My aftermarket sensor seems to work as it would go to red right away plus you could hear the knock. I would then quickly take my foot out of it. When I upgrade my fuel octane I still get a visual sometimes but just the first green...

I have an aftermarket knock sensor installed in my '85. Is it ok to disconnect my factory knock sensor? If I watch my scanmaster at WOT I get a knock indication but nothing from the aftermarket unit. I do not hear any engine knock. I am running 94 octane with some VP C-12. Any direction...

Hi there. Nice build. I have a 1978 El Camino with a 383 stroker. I notice your compressor and alternator are opposite to mine . Could you direct me to what route to take to do the same. Makes things look nice and tidy. Thanks