Search results

Hey all, Thought I would throw it out there that we at Benchmark Tuning are having a holiday get together Saturday December 26 from 10 am till whenever! This isn't a sales pitch day, just a day where guys can gather in the crappy weather and chill instead of messing with the day after...

Hey all, I don't want to offend anyone here but we just opened and will be having our grand opening this Saturday October 10th. I am not a vendor yet, but have been a member here for awhile and would love to see some higher horsepower GN's on the dyno Saturday to represent our community...

Can you post some pics of exactly where you put it? I am going to do the same. Thanks

It looks like there is more than 6volts going to the ECM, If I unhooked the knock sensor.....what else can cause 14.4 degrees of timing out of the motor and the check engine light code 23? Theoretically if the knock sensor is unplugged shouldn't it not pull timing, eg) thats how they...

:mad: Hey guys, I put in the motor I had bought from Chris and hooked everything up....put the new bearings in and each was clearanced at .0015 with plastigage.... However, on startup the car built about 60psi of oil pressure and then shortly after throws code 43....esc failure/engine...

Final Payment also sent, Thanks, Mike

No, didn't dissassemble turbo, the machine shop put a piece of expandable foam in the exhaust housing to ensure no shavings got into the compressor wheel.......

Heres some pics of the turbo.....check out the milled actuator hole! I can only imagine what it would have looked like if I would have done it with a carbide bit 4" inlet 3" outlet and now correct actuator hole size...1 1/8th which is just about an 1/8" under the THDP...

Hey all, Just recieved my 6765dbb turbo a week ago and just had the actuator hole milled out to 1 1/8" to help with boost creep as many have been running into issues. I chose to have my local machine shop put it on a lathe and do it rather than carbide bit method, a little cleaner and only...

Thanks all for the help, Chris replied, and I think we have a solution.....this was never meant to bash Chris as he didn't open up the motor and specifically check everything out.....and didn't have any suspect to...... I'll keep you all posted... Hopefully all this works out and I...

The bottom of the pan just had some shavings in it, figured it was from a new motor, breakin...... The motor rolled over fine, just tough due to compression...... I don't know the clearances set on the motor, I am still waiting on a reply from Chris.... Thanks, Mike

Thats definately not good news:( Hopefully Chris can give some insight on this as I believe he assembled the motor from what he said, and here is the add showing what was done to the motor and that he would stand behind it..... 1987 3.8 gn motor,.030" over with forged trw pistons,resized...

The interesting thing about it, the crank doesn't look scored too bad...... here are the pics a couple of rod bearings..... And here is the pics of the crank itself..... Thanks for the help..... Mike

Sorry forgot #3..... This bearing doesn't seem to have the complete copper showing.....like the others! Thanks Mike

The bearings say Clevite 77 MB-2491P .010 Here are the rest of the bearing pics......can I just replace the mains since the rods don 't show copper? Thanks for the help guys, just hope I didn't buy a bad motor as I really don't know who to turn to to have it rebuilt:(...

There isn't much in the bottom of the pan, just some minor shavings on the oil pickup screen.......Every main bearing is showing copper like this, even across...... The rod bearings aren't showing any copper at all? This doesn't make sense does it? Also did a leakdown before I pulled the...

Hey guys, I bought this motor off the board and was only supposed to have about 1000 miles on it, figured I would replace the rear main seal before installing it and this is what the rear main bearing looks like.......is this bad? Thanks for the help...... I need to know what...

I second sticking with one of the vendors on this site....... I just ordered my 6765dbb from Mike at Full Throttle and they were very quick about getting it to me, and you can't beat his advice either! Trust me coming from someone whom has owned a performance center, nothing is better than...

Hey guys, I am going to put extra engine on an engine stand and was wondering if anyone new the thread size so I can pick up some bolts to bolt it to the stand. Thanks all, Mike

I'll let you know, I just ordered to precision 6765 bb boosted turbo from Full Throttle. Mike said that it has better flow characteristics and is an upgrade from the 6776bb turbo. I'll let you know!