Search results

For sale is a Bob Bailey 2 Step Rev Limiter. It has seen very light use and is in perfect working condition. It comes complete as shown with the original manual and original box. I did trim the wires not used in the Turbo Buick application. $170 shipped

I am selling my Centerline Telstars. The fronts are 15x6 with 3.5" backspace. The rears are 15x8 with 4" backspace. All four wheels are 5x4.75 bolt circle. They are polished aluminum and come complete with centercaps. The tires are 255/60/15 Mickey Thompson ET Street Radials. They are...

This is a 38 mm wastegate. It originally came with a GN1/BuickGN downpipe. It has a 10lb spring in it and is in good working condition. $100 shipped

This is a TA performance 3" Downpipe that I modified to work with my external wg off the header. It no longer has the internal wastegate provision. It has the o2 bung welded in. It is powder coated gray. No dents. Use it to fabricate for your setup. Dump pipe is included. $200 + shipping.

For Sale: TurboTweak 6.0 chip for 60 lb injectors and alky $80 shipped TurboTweak 5.6 chip for 60 lb injectors and alky $40 shipped RJC Powerplate for stock plenum $40 shipped I still have the static proof bags for the chips, so they will ship safely. I will post pics of the above...

This is a PTE GT6157 dual ball bearing turbo. It is 2 years old and is in excellent working condition. $850 shipped + paypal fees.

Used heated o2 sensor kit complete with sensor and instructions. The sensor is 2 years old, works well, and has not been used with leaded fuel. $55 shipped.

I have an intermittent problem that only occurs at highway speed. The car will cruise along fine and then randomly "missfire". The rpms sink, car goes lean, it will buck and surge, and occassionally backfire through the exhaust. The car idles fine, accelerates under boost fine, and slow...

I have had flaky IAT readings for years. I know the sensor is not really used for anything, but I want to go to speed density where the sensor becomes important. Today I turn the key on engine off and the IAT reading was 156 and dropped to 139. I started the car and there was a rapid drop to...

CAS V4 stock location intercooler. Complete with shroud, mounting hardware, and bracket. Very good condition. I had the shroud welded so it is one piece and you don't have to mess around mating the two halves. $500 shipped obo.

My driver's side rear wheel wobbles when the tire is rotating (from positive to negative camber). Here is what I have done so far: Properly torqued lug nuts, changed wheel for known good, changed out drum for known good. After this I put the car on jack stands, removed the wheels and drums...

I've been chasing down vacuum leaks as a result of high BLM's (140-141) at idle. Through several different detection methods I eliminated a few leaks. My BLM's rest at 130-131, but only with the PCV valve port on the vacuum block capped off. Once I re-connect the PCV line the BLM's climb...

PTE Turbo Saver. About 1 yr. old. Very good condition. Complete with instructions and 2 new WIX oil filters. $130 shipped.

I need a 700r4 filter and TCC solenoid. If I tell that to the parts guy I know he'll look at me like I don't speak English. Can one of you guys give me a year, make, and model of a vehicle that would correspond to the parts I'm looking for?

Been doing a lot of research and I feel that a set of ported irons would be my next logical mod. I want to bounce this thought off the board cuz if I'm off you guys will set me straight and save me $. If heads are in my near future I will have a lot of follow up questions, so bear with me...

I am a track novice. This is my second pass ever. 60'=1.655 330=4.839 1/8=7.584@89.28 1/4=11.988@110.83 Car was weighs 3810 with me in it, and was on 255/60 MT DR's. I was at 24#'s boost, launching at 10#'s off the footbrake. I was also running through the exhaust. Please review...

Just installed Biondo line lock Biondo Racing LL - Sam Biondo Line Locks - summitracing.com. I have it after the proportioning valve. I am sure I have it plumbed properly as I followed the many detailed instructions on this site. It works normally when engaged, but to disengage it I have to...

Is there anything in the NHRA rules regarding placement of a line lock (specifically before or after the proportioning valve)? I want to install one, but the one I go with may depend on the answers you guys give me. Don't want to get tech'd for a small oversight such as this. Thanks

Due to child medical costs, a buddy of mine is forced to sell his pride and joy. It is a 1985 T-Type. 89,000 mi. White with the black out package. Hard top. Motor was rebuilt several years ago. It has had a repaint. There is some minor rust starting on the bottoms of the doors. Garage...

Who can I trust to buff out my GN? I am looking for someone local. I am in the far west Chicago suburbs (Wheaton, Naperville area). Also, what can I expect to pay? I also posted in the resto section, so I apologize for the duplicate.