Search results

Does percentages apply when adjusting fueling on Eric's chip ? If my O2's are 900 in first gear and if I lower them to 115 which removes 10%will my O2's drop to 810 ? or is it trial & error ? I know there is an overall fueling adjustment that also impacts 1st gear fueling too. I just want to...

Anybody use the 8.5mm universal kit that MSD sells to make your own lenght wires ? Just curious about how the crimps turned out with the tool that comes with it.

I am trying to get some kinks worked out and am going in the right direction but the maf is throwing me a curve and effecting the fueling. On Direct Scan at wot I am only getting 170 g/sec @ 4650 rpm while accelerating. Now I tried another 87 good maf and there was no difference. I still have...

Just seeing what you guys think of this. The solenoid is mounted to the pump plate. Almost done :biggrin:

Is the round beveled seal still available anywhere ? Or has anybody came up with another method of sealing it besides loading it up with hi temp silicone?

What is the other line on the wastegate for ? It is the one that goes to the vacuum block. Also has anybody sucessfully used an RJC type boost control valve with a stock wastegate to run higher boost ?

I understand all the good that can come out of adding Razors kit to a HA car, just by reading what a lot of you have been saying about it. Let me say that I am not trying to make a strip car and I am not going to race it. I really have no time goal in mind just to have it run stronger and not...

Here you go :) 84GNGary's Index Page If anybody has information on any options I don't list please let me know so I can add them.

I am going to make a blank off plate but I want to make sure I get the right port closed off. When the engine is building boost the flexible steel line that goes under the TB and connects the EGR valve to under the turbo outlet becomes pressurized. So this then pressurizes the top side of the...

What I have read is that they are good for the cars and let the engine breath better. All the ones for sale I seen say for 86/87 only. Will it fit an 84 without any problems?

How much of a PITA is taking off this header so I can have the cracks welded. It looks like the up & down pipes will have to come out, now what about the gaskets or seals between the pipes and the turbo. Can they be reused or will they be useless, then what do you do ? I am going to stick with...

A few months ago the a vac line blew off and it sort of back fired while under boost. I replaced the vac line and all was fine. Today I found the MAF screen inside the air filter box. I flattened back out and sandwiched it between the retainer rings. Should it be okay or is there anything else I...

Alright http://carmotorsports.com/ e mailed me back stating that they would most definately be interested in producing theses hoses for us. So far we need the top radiator hose, and both heater hoses by the firewall. There are also two hoses that are by the water pump that go to the heater...

If a new top radiator hose was made from the measurements of an OEM hose and the proper material would you buy one? And if so what would be your maximum price range you would spend for it ? This is only in the discovery phase now but I found a company that can custom make rubber hoses any...

Did not use the car for 1 month the first time I started it the brake warning light came on and it was due to a hydraulic problem. Bleed the back brakes using a helper and the pumping method, light still on. Gravity bleed the fronts (helper had to get dinner) fluid kept comming out and topped...

Have'nt used the car since December which there was no problems. Started it up today and the warning light came on it went out once then came back on again and stayed on for 15 min till I shut the car off. Have stock hydroboost system. Just installed new calipers, wheel cylinders & hoses last...

I just fixed my non-working sending unit which was causing the gas guage to malfunction. Since there are a lot of posts regarding this I took pictures and wrote instruction on how I diagnosed and fixed it. I attached it to a link on my web page for all to use. The only thing is that I do not...

My new filler arrived in okay condition, scratched, scuffed and dull looking. They cannot go on the car as is. Took them to a body shop (an old friend of my wife) and was told about $300 to sand, go over with with polyester, prime, paint and clear coat. The finish on my car still looks new and...

I did a search but could not find what information is actually displayed on a scantool with the different ecm's. All I have read is that you should convert it over and it will give you more information for tuning, etc, etc, etc. What info does the 86/87 ecm give you on a scantool that an 84/85...

I found this on their site, just seeing what you guys think about it or if anyone has one. It's about $200 for the complete kit. The only thing is the hose they give you is 70 mm which is about 2 3/4 in diameter. Would that be too restictive? http://www.knfilters.com/universal/apollo.htm