Search results

Been holding onto this since my upgrade to FAST.. Time to sell it. $200 + $10 shipping Firm

I've got a buddy that has a complete industrial machine shop with all the goodies including a large CNC machine. He wants to do up some torque plates for me. Does anybody have exact dimentions for the head bolts and bores. I'm sure I can go off my block and heads but I'd rather get it from...

I need a sanity check.. Just about to order the following ring set from JEGs: Total Seal JM4000 Total Seal OE Quality Piston Ring Sets They are for a 4.000 bore.. I assume that I can just file fit them? Thanks.

I have some galling of my rod K1 H beam rod pins and I want to get new pins however I figure I need to also replace the brass small end bushing. Has anyone done this before? I talked to K1 technologies (now weisco) and they couldn't find any replacement bushings and because of the buy-out they...

I just bought a shortblock and found that it looks like there is a wire ring pressed into the deck of the block.. Have anybody seen this before? I have heard of grooves milled for fire ring in the heads but I havent seen a ring in embedded in the deck of the block before. Trying to find head...

I need some help.. I just have swapped out my converter from an Orange Stripe to a Vigilante 5 disk. I amd not positive what my stalls should be for either however I am wondering if anybody has the same results as I do for these two converters. I put my transbrake on and revved until I saw...

I was wondering if I need to pull the engine to remove the oil pan. Do I need to do this? I also have a girdle. TIA Don

Hello all, I think I've got most of the driveability stuff sorted out however I'm about to tune for WOT soon and I need some example AE and AF table that's close.. I like to learn from example :D. Would anybody out there be willing to shoot me a somewhat close VE table and AF table file for...

It looks like the TV location is leaking big time on my 200r4. I have recently replaced my transmission and engine and the gasket for the TV hole must have got lost. I assume it uses a gasket here.. Can I just cut one out of cork? What have the rest of you done for sealing up the TV cable...

Moved up to Fast XFI and I no longer need these. Gen 2 Translator - $200 Modded ECU - with TT chip - $200: TT chip Setup for - 82lb inj - Razor's Alky - 92 pump gas - 22psi max boost - GT6132 turbo - Orange Stripe Torque converter (3000 stall) - $200 - G-body SLIC - stock cam Thanks

I've been having a problem since I upgraded my brakes in the front and back. I put Baer sportstrack 12" in the front and PBR 11" disks in the back. I have blead all 4 corners and the pedal is very very firm so there appears to be no air in the system. I also have a vacuum booster upgrade...

- Perfect Chrome Stock Valve Covers $150 shipped. - New RJC Stock Billet Crank Pulley with Freshly Chromed stock fan mount $170 Shipped - Race (under-drive) Crank Pulley with Billet Stock Fan mount - $75 Shipped - Stock Intercooler fan - $30 Shipped - Stock Fuel rails - $40 each. - Painted...

Any FAST XFI Tuners out there who have actually used the feature that allows them to tune over the Internet during a Dyno run I'd like to hear their experiences to see if it's practical. I want to get my car tuned shortly but I need a good tuner to do it remotely. Don

Turbo GT6152 from Full Throttle - Used for a summer some weekends before moving to a bigger turbo. No strip use. No noticeable shaft or end-play. $550 shipped. Kenne Bell Valve Covers.. Powder Coated crinkle texture.. Clearanced for Scorpion Rockers and GN1 Heads $150 shipped. Perfect...

I have noticed many times that the web site times out when redirecting from the home page when loggin in with a 404 message on the following link: http://www.turbobuick.com/profile.php?do=dst This is very annoying and quite repeatable and has been happening for months. If I manage to click...

I am selling my set of very nice "Weds Bavaria I (Bavaria Fins)" rims and wheels. You won't find these anymore and they are very unique. They were popular with BMW's in the 90's. Below is what they looked like on the car before I moved to 17" Intro wheels. I'm looking for $800 for the set 4...

I bought an XFI from another buick member some time ago and now I'm about to install it however I don't know who made this harness. Originally I though it was made by Caspers however after looking at their catalog it looks like they have a cable/adaptor box which is not like what I have. Has...

I just did a compression check on number 1 so that I could dial in the cam sensor and it appears I have zero compression on this cylinder. Other cylinders look fine. I know that this engine was good before I put the new GN1 heads and roller Cam, roller rockers and double sprocket timing chain...

This question is for TR Customs... I am thinking about taking advantage of your discount and buying your headers... I am assuming that there are no clearance issues with GN1 Heads. I have seen clearance issues with some headers and the tabs for the additional head stud mounting holes compared...

Guys, I have the following for sale: Champion Irons - Appox 12 runs and 1200 miles on them. - $900 Freshly Ceramic Coated gbodyparts 3" downpipe - $400