Search results

hey scott hope you see this but could you give me the info on the machine shop here in vegas you recomended. thanks

Ive been saving up money to finally get my buick back together and have been buying a few things in the mean time that i would need fo rmachining.I was lokking for a machine shop close by vegas like in cali or arz, you know like instead of shiping it i would like to take a small road trip out to...

was wondering if i could use the hot wire kit with any of the double pumpers that are avaliable out there.thanks.

Im getting ready to take my 109 block to a machine shop but have a few questions and maybe you guys could give me a few questions to bring up to the machine shop. first of all to bore the block is .30 over done for maximum performance or due to damage on the block, my block has no damage so if...

ive been looking into getting an xp double pumper fuel pump, but a friend of mine said he read some where that you could use two walbro 340 to work the same as dp. does any one run this type of set up or has anyone ever seen it done. thanks:)

well i was driving down the road at about 35mph when this old lady was going about 25mph in front of me. So i decide to pass her up and mash on the gas to get past her once i got passed her this loud pop came from the car and it shut off. I pulled over to the side and tried to start it back up...

you know like a total package (pistons,rods,crank ect.....) for a single price all together, or would it be best to shop around and get all the internals peice by peice.

i was coming home last night from the track and after running a best of 11.8@114 60ft1.6 @22lbs of boost, i had one last run and it was against a supra (a pretty fast one 11.6) so i raised the boost to 24 and raced him at the track. I lost and ran a horrible time of 12.1@113 60ft.2.0 pathetic...

i was wondering which shifter i could instal in my buick without having to modify my center console to an extent. i want to keep it looking stock as possible. meaning i dont want to cut anything out of the console. i did check out that pistol grip shifter looked looked really bad ass...

just installed new transbreak and just learned how to use it last night and one of the nifty things i learned was, how to get the front wheel off the ground, he he he. That was a time of 12.4@111 with a horrible 60ft. 1.8 supra status. hopfully 11's are in out reach because our best time was...

im really excited because i just got my new trans break installed. never have used one and tonight will be the first time at the track to use one. i gave it a little test out on an empty street and launched at 10lbs of boost. i have to leave the car in 1st and build boost and accuratly shift...

can anybody tell me what the tourqe specs are for the intake manifold and also the tourqe specs for the stock rockers. thanks

i hooked up the fuel pressure guage and dont get a reading at all the car wont start and was wondering if the line that goes to the fuel pressure regulator is a return line or not. could it be that my fpr has gone bad or is it something else. thanks in advance

sounds like my fuel pump is having a hard time pumping fuel because the car is stuttering alot and the pumps sounds really loud in the back even while im driving i can still hear it. im planning to drop the fuel tank and check it out. wondering if there were any other suggetions you guys...

now dont get me wrong, a 12.7 is not bad in fact its the fastest ive ever gone in my life, but im kinda wondering if i just babied this monster and didnt really let it unleash its true power.12.7@105 w/18lbs of boost and launched the car at 6lbs of boost with some slicks at the track. let me...

If I disconnect the computer without disconnecting the battery could I have ruined it?

ok check it out, new crank sesor, good cam sesor, good module and coil, now all of a sudden i'm not getting spark. the car would run then shut off at 180 degrees so i disconnected the harness from the computer then put back and now it wont start (no spark). all fuses are good, timming is good...

i was wondering if there is a method on testing your ignition module to see if its bad. thanks

ok check it out today i started my car up and its been a long time since i just finished putting it back together. I got the car to start with eaze and it idled goood and sounded good so i decided to take it out for a spin. i was able to drive down about 2 miles down the road with no problems...

can i use a hyd roller lifter fit for a chevy in my buick. see i have one bad lifter and it came that way brand new. Its the only thing holding me back and need to know if there is a lifter out there i can use as a temporary till Anderson Performance Automotive 8209D Rosebank Avenue Baltimore...