Search results

I have a 2004r trans and d5 converter that came out of my 1986 Buick T-Type. Car is gone and I no longer need the trans. Asking $200 for the trans and converter. They might still be fine but I am selling them as cores. I accept cash in person or I will consider using these as trade for or toward...

Selling a pair of Mickey Thompson ET Drag slicks I never used. 28x10.5"-15" size. Asking $185 for the pair plus shipping. If you are close to Chattanooga I will meet you for a sell. E-mail me at Noah.Holcomb@gmail.com

I sold my T-Type, now I'm clearing out some of the odds and ends still laying around. I have 3 new in the box Denso oxygen sensors part # 234-1001, $15.00 for each sensor. Shipping is $5 no matter how many you buy. E-mail me at Noah.Holcomb@gmail.com

1986 Buick T-Type HARD TOP with burgundy exterior, and interior with 108269 miles on the chassis, the title is CLEAN! The car has been garage kept since I acquired it in 1999 and was repaited only a few months before I became the owner. Upgrades Rebuilt bottom-end with approximately 5000...

1986 Buick T-Type HARD TOP with a just a bit over 100K miles on the chassis Rebuilt bottom-end with approximately 5000 miles on it Speed-Pro forged pistons Speed-Pro molly rings ARP mains, rod, and head bolts Melling oil pump kit stock graphite type head gaskets 202/202 Postons cam with...

Hello, I was wondering if some one could run a car fax for me on a car I am looking at, I got rid of my Honda and have been looking for another SAAB. I had a 9000 a few years back and it was a great car, any ways the information is listed below. Any help is appreciated, so thanks in advance...

Does any one on hand have a picture of the spring arrangement for the rear drums on our cars? I just put C-Clip eliminators on my car and have been putting the brakes back together. I seem to remember where most everything goes except for one spring, I think it is called the adjustment spring...

I am installing a new set of axles with c-clip eliminators, but to do this I must remove the old axle bearings and seal but this is holding me up as of now. I don't have a slide hammer handy so does any one have an idea on how to remove these things without one?

Does any one know the stock GM axle bearings inner and outer diamater?

I am selling my BRF valve body 200-4R trans out of my turbo buick, it worked when removed and has around 100K miles on it. I am selling this as a core though. $300 if you pickup the trans in Chattanooga TN

I am selling my 200 4R BRF trans. The trans has a little over 100K miles on it and is stock. It was working last time I drove the car with it but with this many miles I am sure any one that buys it would be buying it as a core and rebuild it. I would like to avoid shipping this item...

Does any one have this car or is it true the car was wrecked and parted out?

have been needing to freshen up my cars rear end for awhile and was looking at going with either moser or strange 33 spline axles, full spool, and c-clip eliminators (and hope they don’t leak), The car will be raced a lot, and I put less then 3000 miles on the car in a year so I can get over the...

Quick question, what does the gas tank in our cars weigh when it's empty? I was considering a fuel cell in my attempt to get the car as light as I can and wanted to get an idea how much weight I could shed from the car.

I have been trying to get my car to be as light as I can get it while not having to resort to fiberglass body parts, and retaining most of the stock interiors appearance, with the exception of the pulled passenger seat for the track only. So far I have done the following Pulled the...

I have a short tail-shaft BOP pattern TH-400, I know I must change the yoke to a TH400 type but will the driveshaft it self need to be shortened? If so, how much and what length yoke should I use. If not what is the proper yoke dimensions for the stock length driveshaft. Any help is...

I need some maps for the 83's any help is appericated even a base map would be great. Mail to TwoLaneBlackTop8aol.com

http://forums.nasioc.com/forums/showthread.php?threadid=442510&perpage=25&pagenumber=1 I can understand if some indivisual was selling the car but this is a new car from a mitsu dealer. They should have sold him the car or sold him another just like it :mad:

What is it with this film. Notice I call it a Film not a documentry. As a documentry needs to be made from facts. I watched it and could tell right away this seems to be fabricated and oh how I was right http://www.hardylaw.net/Truth_About_Bowling.html So I had a conversation with a person...

I have been thinking about ditching my 202/202 cam fo a long time now and have been looking into the 218/218 for some time. I know it is a bit bigger but I am still interested in it. Who here runs this cam and has had good luck with it? My final goal for the car is a 10.5 in my car. (car is...