Search results

I know this has been ask before, but what size bore do I need in the waste gate hole on the turbo? It's running 25lbs and I have the boost control turned all the way down.. Thanks, James.

Just was wondering if anybody knew the arp head bolt torque specs for iron heads thanks. James

Does anybody know if the atr style headers will work with a TA down pipe. Was thinking of going that route but need to make sure it will fit without any problems. Thanks

Ok i know iv seen on here somewhere that mentions the best location for the wb sensor but i cant find it anywhere. I thought it was down low on the dp, but i see the ta dp and its got the bung at the top. Maybe thats for a egt gauge? Need a dp and just checking before i buy one.Thanks

I have a PSLIC and a 3" inlet turbo. I want to step up to a 4" inlet turbo, but right now my 3" inlet pipe and 3" up pipe are touching one another. So does anybody have pics or advice on a 4" inlet and a 3" up pipe set up? Thanks for any reply.

Looking for a 3 DP. Pm me what you got. Thanks

Im doing a different combo, so i have these parts for sale. Dutt neck intercooler with very nice weld. $150.00. Ta-49 turbo bought from kirban in 2009 $275.00. 36lbs lucas injectors w/ultrachip and tt chip. dont want to seperrate $225.00. Stock rods with arp bolts, one rod has minnor...

Nice stock intercooler w/dutt neck. Very nice weld, deliver to buick nats. I will be there thursday thru sat. 150.00 Thanks James

I heard that by installing a clutch switch you will gain 3 to 5 mph in the 1/4mile. Wouldnt this be bad for the torqe converter. Thanks. James

Ok i was out driving the GN yesterday and when i go part throttle and boost comes up and i hold it at part throttle the boost starts to flutter. Is this normal And if not what do i need to do to stop it. Thanks

Will a set of 275/50r15 fit on stock gn rims or do i need to have the widened?

Does anybody have pictures of a Precision SLI installed? I would like to see any if possible, to see what it looks like and see how tight it is. Thanks.

OK you guys have heard this probably a million times but, i just want some thoughts. Fuel pres. goes to 50 lbs at 10lbs of boost good right, now as i go to 15 or above it starts to drope all the way down to 40lbs and it stays there. So whats your thoughts? Thanks Jamie

Went to the track last week and did one pass, 02s on the powerlogger started out around 811 and dropped to 740 at the end, and the timing in 3rd and 4th gears at WOT was 17.3 . My question is do i need to add fuel in WOT fuel settings to raise the 02s or is that good, and do i add timing to 3rd...

Does Anybody or does anybody know of somebody that has a complete air ride suspension on a turbo regal? Im thinking about installing one on my regal and would like to hear from somebody that has seen one or has one. thanks for any replies

Who sells a wastegate soleniod for these regals, Ive did some search and found nothing. thank for any help.

Iv been taking my motor apart and noticed that the crank gear is a little loose, my question is how loose should it be? I know im not suppose to compare it to a small block chevy, but the small blocks that i have built has always been tight, i have to tap them on, this just falls right on and i...

I have a 2800 stall converter that when i bolt it to the flywheel the flywheel is wooblying and when i unbolt it the flywheel is tru. Is that a unbalanced converter. and what will it do if i run it like that.

I took my plenum off and there is gas on my rjc power plate. I think its alot since the injectors are below the plate, i still have the egr hooked up and it was alittle rich at idle ,could a bad egr cause this? Any thoughts would help thanks.

if i have .02 th of rod side clearance would it sound like some bad rod bearings? thanks for any help.