Search results

I need one also, wiling to get a spare too.

Give me an e-mail and I will get them to you as soon as I can. I have a couple of phone pics to get you started

Yes that would be it, next time you come to Foxwoods stop by the Scorpion Bar and say hi. Ask for Tom at the door.

Found an all original bone stock 87 with around 100k on the clock. A quick look and I didn't find any obvious problems other than it needs paint and fillers. Put some fillers on it and buff the paint and it would be a nice DD. Guy wants 8k. P.M. me if your interested I might be convinced to...

I am in CT. Right now I am waiting on an adjuster, the ins co. uses a formula and right now the formula says it's totalled, I say it's not so the adjuster has to look at it. Thanks for the prompt replies.

So yesterday I proved that I'm pretty stoopid, rear ended a Ranger, hard on the brakes just tapped him and took out: hood grill header panel headlight buckets headlight bezels corner lights fillers radiator support I would prefer the correct grill, but I'm not gonna be to picky...

Getting a new nose starting tomorrow, I'm pretty stoopid:redface:

Out and replaced. Took about an hour of actual work. I drilled out the rivets. Thanks for the help. Window works so much better that I am going to replace the passenger side next week.

Got it thaks door panel does not tremove. Remove 3 10mm nuts holding the glass to the regulator remove 2 10mm nuts holding the track by the arm rest drill out the 4 rivets. get the glass up out of your way and finagle the regulator through the opening in the door.

My driver's side window is stuck down, pulled the switch and checked voltage to the motor. It is the motor, how do I get the F@(#)@! thing out?? Does the window have to be up? I figure it probably soes since it is stuck down. Any help would be greatly appreciated as it is supposed to rain...

Interested in many parts, where in Ct are you?? Interested in: Headers Headlight bezels rear bumper fillers Turbo. up pipe and down pipe thanks

84/85 headers Are they still available?? If so how much shipped to 06351. thanks

Dude....check your P.M.'s............

Pretty engine dude...does it still run like crap??? Anyway back to the thread, try this link, it has mucho info: http://www.turbobuick.com/forums/hot-air-non-intercooled-tech/33080-basic-hotair-info.html

I had what sounds to be the same problem....here is what I found and fixed, not sure what caused the problem but it runs great now. New Vacum line to the EGR, new line to EGR control solenoid. New EGR control solenoid and boost control solenoid. (had both on the shelf and changed because I...

Modern Pro Stock Valve springs are 450 # on the seat and over 1200# over the nose. They get changed once they drop to 350#. They use Beryllium guides and seats. Valve sizes are over 2.5 fo the intake and 1.8 on the exhaust and a 2.300 installed height. Non cryo valve springs last a pass or so...

O.K. I have a strange one: When starting cold my speedometer doesnot work, after I have driven about 10 miles the Speedometer needle will start bouncing, after about 15 miles the speedometer appears to work just fine. It happens the same way every time. I have checked everything but the...

Dude, that pic really makes me think you have a gasket problem, your A/F problem makes me think it's the intake. I could be all wet but I would try the starter fluid trick once the engine is warm and your A/F leans out. Look for the leak to be around the center of the intake on each head...

Looks like oil in the water, head gasket or intake gasket.

My wife doesn't like the car much....she can't reach the pedals.....and she is always amazed about the amount of thumbs up and "nice car" we get when we are out in it. A while back I had a guy come up alongside at a stop light and yell.."nice car is that a Monte Carlo?". I replied "why do I...