Search results

Looking for a good 109 turbo block and heads as cores. Prefer Canada to keep shipping costs down. Thanks Nolan Nolan@campbellautomotive.com

I have found the same thing. The GN's have a much better ignition system than a SyTy. We had major problems with the normal ur or TR NGK plugs. Once we swaped to the IX iriduims all the problems went away. We run a TR7IX (vortec heads) gapped at .028-0.025 with 28-30psi and meth with no...

the most common set up is 275/40/17 front and 315/35/17 rear. Nolan

It was at the end cap, I think we just over tightened it is all. Never had a problem before at all. We have done a bunch of 3.8stuff already. I will get Mark to put the vid up on our web page. Nolan

I have alway ran the biggest, stickyest tire that could fit on the front. No use haveing the AWD if you are not going to use it. Nolan

Turns out this turned out to be a crack in the brass filter. We noticed it when we where taking it apart. If you watch the vid close the filter is right behind the turbo. Nolan

Stock block with 4 bolt mains and partial fill, stock crank,eagle rods, wiesco pistons (9-1), vortec heads ported, stock manfolds ported, Stock intake ported, 84lbs injectors, single 255 with boost apump, PT-74Q, stock ecm. 28-29psi 91 pump with meth. We just dyno tested the twin to this...

I'm in Thanks Nolan

Hey there the V-band is a 4". It is a standard bearing design. I belive Turbonetics makes a BB88. Nolan

Brand new never used Mid frame T-88 turbo. Turbo will support 1250hp. Asking $1200. Nolan Nykyforuk www.campbellautomotive.com

Selling my 2015A Weldon pump it has 5000miles on it. Asking $500.00obo. Plus shipping Nolan TurboV6@telusplanet.net

I enlarged the Wastegate hole on my GT76 to 1.4". This was a big mistake. By doing this I enlarged the hole by 60% which brings the back pressure onthe wastegate puck from say 15psi to 24psi. I have a 19-35 psi accustor and could only get 22 psi out of the turbo. 35psi -60%=21psi so close to...

Nope there are no tranny controls in the 7749. You would have to run a seperate PCM to run the tranny. I run a 8625 to run mine. Nolan

This sounds to me like the eprom is not seated properly. I had this happen to me last week. Set a ton of codes and ran like crap. Might be worth a look. Nolan

I have never tuned 55's or 72's so can not say how they will work. I have done quite a bit with the dephi 75's and run the 84's in my truck. With the 84's drivabiltiy is great my wife drives the truck and says its better than hers:rolleyes: Guess I should get busy and drop the built motor...

Well advantages would be #1 it can be used with a 3 bar map sensor (Thanks to Brian Green) #2 you can datalog a wideband O2 with the proper code hack.( Thanks to DIG) #3 its speed density so no Maf #4 with tuner cat RT and the romulator you can make changes on the fly like a FAST...

Email me at TurboV6@telusplanet.net with a build list and I will see if I have anything close. If I do it will be for 75's or 84's I do not have anything for 55's. Nolan

Bruce could you e-mail me I have some questions for you on the DIS and 7749. Thanks Nolan Nykyforuk TurboV6@telusplanet.net

Would you be interested in selling those 75's when you upgrade to the 95's?. If you are let me know how much you want for them. Thanks Nolan Nykyforuk 780-818-7483 TurboV6@telusplanet.net

Any one else have any info on this? Thanks Nolan