Search results

Selling a set of 6 Bosch 160lb injectors with the following part #s stamped on them: Bosch 0 280 150 846 and FORD XL3E-C9A. These are sometimes referred to as "white tops". Just had them cleaned and flowed by Fuel Injector Connection but want to go in a different direction. $365 shipped in...

Looking to buy a .81 ar turbine housing for a TE-45a. PM me if you have one. Thanks,

Upgraded to larger injectors and have a set of 6 MSD 50# for $155 shipped.

Have a couple of leftover parts from conversion. Everything - $20. P.M. me. EGR Solenoid - $20 shipped Crank Sensor - $20 shipped WG Solenoid - $20 shipped Harness Cover (decent shape, no cracks) - Make offer if you are willing to pay shipping B&M Round Shifter Knob - $20...

Going standalone sale. Scanmaster 2.1, $165 shipped Stock ECM, $60 + shipping MAF, $20 + shipping Accel 8.8mm 300+ Spiral Race Wire Set, $40 shipped Ignition module & Coil Pack, $110 + shipping TT 5.6 chip for MSD 50s, 100-octane, 20-23psi...

Looking to buy a BGC 3" elbow. PM me if you have one.

PM me if you have one for sale.

Bought a car and was told it had 40# injs with a Red's chip, so I had Eric make me this chip with a a planned switch to 60#ers. Took the car apart and found it actually has MSD50s with a TT chip, so I do not need this new chip. It was made 3 weeks ago and has never been installed. It is a...

This kit was on a car I just bought, but I will not be using it. Looks like the previous owner used a windshield washer mixture. Kit is complete, $100 + shipping.

(6) Delphi 75# injectors, $225 including shipping to anywhere in Continental USA. If you have a T+, I will throw in an Extreme chip for these injectors for $20. The chip is left over from when I ran a 4.1L and I need to get bigger injs for the current project.

Selling my Pat's 10", 3500 stall that was built for a 4.1L and has limited use. Was hoping to reuse it behind a 2JZ but it is way too tight for the higher revving 3.0L. $275 shipped to anywhere in the continental USA.

PTE .63 exhaust housing for P-trim. WG hole has been opened slightly and has minor porting (radiusing) on the inside of the WG hole to improve flow. $100 shipped in USA. Will consider a trade for a P-trim T04 housing with V-band or 4-bolt.

Check my ad in the Classiifieds.

This is a modified 2nd-gen RX7 (86-91) K-member to make a Buick V-6 swap a bolt in. The steering rack has been moved forward to fit BETWEEN the damper and the pulley allowing the engine to sit lower than other swaps and allows a 3" DP to fit easily. $375 + shipping I am also selling a custom...

As the ad says. Email or PM me.

Looking for the big compressor housing with 4" inlet and 2.5" outlet. Can work a swap + cash if you are interested in the smaller housing.

Recently broke my tranny and switching to a TH400 so my converter is up for sale. It is a like-new Pat's 3500 stall 9" NLU. Has only been in the car (RX7) for a couple of months and has maybe 600 miles and 12 pases on it. Cut a 1.50 on the footbrake w/o much effort. $320 shipped anywhere in the USA.

I believe it is part# TA301. How do you like it? Do you have any pics you can share to see fitment, especially from the side of the car? TIA,

What would cause fluid to flow out the vent tube at WOT? To avoid the easy answer, the tranny is not over-filled. TIA,

Often discussed topic but I am looking for a definitive answer. Are these the same cam, just different branding? Availability and price from Summit makes it attractive but want to make sure they are identical. Not looking to debate the pros/cons of this cam or the need for a cam upgrade.