Search results

Hi all, I have one of Julios older alky kits never installed and I'm stuck on step 7 under hood wiring to spiral green and tan wires but there is a plug to connect to something. I didn't see anything in the instructions where to plug this into? Where does it go? Thanks!

Just messing around and listening to the radio and the head lights and interior lights will not turn off. I dont get it. I had to disconnect the battery to turn everything off. anybody know how to fix this issue? thanks George

Please call or e-mail me if any of you guys have one for sale. Thanks George gnxv6@hotmail.com 1-248-894-7850

I think I have a rod knock after a wiped cam nightmare and now I put a roller in it. The knock I hear is very slight. You have to listen closely to notice it. Also, it is only apparent when the car is running hot. Do I have to pull the motor and rebuild it again or can I just replace the main...

I have a 206/206 roller with adjustable timing gears to advance or retard the cam. Can I retard the cam 4* to make it a 210/210? Is that how it works or does it have to be degreed to stay at 206/206? I want a little more top end power. Thanks George

What is the recommended stall for a 210/210 roller cam with a te-44 turbo? Ive been looking at those pts extreme converters. Thanks George

I had a knock problem at 13lbs of boost and my fuel pressure was set at 43lbs line off. I decided to keep raising it a pound or 2 and eventually raised it to 50# to get rid of the knock and my o2's finally got up to the 800mv range. This started happening when I put a roller cam in that I had to...

I was driving my 87GN today and all of a sudden my check engine light was flashing very very fast and my scanmaster would not read or display anything! I was only able to get the car up 30 mph to get it home. Has anyone experienced this before? Thanks George

I'm running 15#'s of boost and half the time when I go WOT I get 820mv on my o2's and 0 knock and the other times I get low to mid 700's and 5 counts of knock. Is this a possible faulty fuel pump? I do not have a external fuel gauge to read pressure while I drive. Thanks George

Can advancing a cam cause spark knock? I switched to a roller set up with the same duration and decided to advance it 2 degrees and now I get spark knock at 13lbs where before I was running a flat tappet at 16lbs. Any input? Thanks George

After I installed this dp I can only get 12lbs of boost. I made the wastegate rod shorter and adjusted my bleeder valve to the max and I still can't get any more boost out of it. It spools fast still like my other dp did so I would'nt think it was a puck problem. Can it still be the puck not...

I ordered a 206 roller cam kit and came with 853 roller lifters and pushrods. This kit is for stock heads. Does anyone know the length of these pushrods or what length do you guys use with stock heads and 853 lifters? Thanks George

Is a 275/50/15 tire the same height as the stock tire? Will this also rub against the frame? I want to put the widest drag radial on my 87 GN stock rims but maintain the the same height. Thanks George

My car starts up just fine when it's cold, but if I drive it for even 5 min then shut it off then turn it back on and put into gear it wants to die on me. I can even tell a little bit when it is cold then put it in gear the car takes too long to get used to the load then finally adjusts itself...

Can a MAF still be bad even though it reads good a/f numbers? I get 5-6 idle 255 wot I'm still working on this stupid intermitent idle problem:mad: Thanks George

Can a bad maf cause the car to stall once in while? After the car is running for a minute or so it wants to almost die when I put it in gear and when it gets hot it stalls once in a while. I have my scanmaster hooked up and looked at all the sensors and appear normal even maf settings. I also...

I got 20* of knock while my tires were squealing and then on the highway I get around 2* wot 80+ mph. It only happens when the tires really break loose. I'm only running 15# of boost @43#'s of fuel pressure. Is this normal to do that? Thanks George

Does this product really improve the handling of the GN? I've been thinking to purchase this and was wondering if it's worth it. What's your guys experience? George

I put a new cam in recently and the car runs great, but when it gets hot it idles like crap for a while and then it gets better and back to crap again. it;s not consistant. I triple checked all vacuum lines and sensors and can't find anything left dissconnected. It doesn't quite act like a bad...

Hey guys, I went from a 206/206 flat tapppet to a 206/206 ROLLER and I get alot of lifter noise after installation due to low preload and I when I took the car out for a drive for about half an hour to get the oil hot to see if the lifters would quiet down, I noticed the turbo seemed to spool up...