Search results

If you still have the drop spindles and springs let me know. Ill take them. I dont need the ball joints but if you want to ill take them. Let me know. Brendan

have you sold this system yet? is not let me know. Is this a brand new unit or did u take it off of your car? Let me know, im interested, Thanks!

I was trying to avoid taking the heads off and opening up the block. Im just debating on just sending it out since winter is coming up. I was trying to just stick to bolt ons but I think I am going to send it out afterall since it is out of the car. I dont want something to blow up after I put...

Thanks for all of your knowledge guys! I will take on this project first thing tomorrow after I get home from work. I knew I asked the right people! Takns again

I have a relatively stock block that has been sitting on an engine stand for the past 5 years. I kept oil in the motor and all that. I am going to do minor work to it like a cam and replace the valve springs, injectors, headers, turbo and all the sensors, wiring and high output distributor. Do I...

I was wondering how to get the heater box out of my car. It looks like I have to take the fender off of the car along with the inner fender. I wasnt sure if there was some way to get it out w/o removing the fenders. Any help will do, thanks guys! Brendan

I was looking into installing a 12pt. cage into my '86 GN. I currently have the dual A-pillar gagues on the car now. Is that something I will have to remove due to the bar coming down the A-pillar or can I still be able to see them? The other question is who has the best cage out there. I am...

I found a bracket in my trunk that looks familiar but I am not so sure as to where it goes. I think it came from under the hood on the front drivers side fender well. I am not too sure though. Any help would be appreciated. Thank you!

Sorry guys I was referring to an oil pressure gauge. I am goin to tie into the lower coupling of the oil feed line for the turbo. Thanks for ur help and sorry for the confusion.

I have a mech fuel pressure gauge that I purchased for my car. What is the easiest way to hook the line up? Can I tie it in to the Oil Feed line for the turbo or is there and easier or better way on doin this? Any help would be appreciated. thanks guys!

I am installing a new electrical auto meter water temp gauge into my car. Can I tap right into the water temp sensor on the front of the engine or will that not work? Thanks in advance

Thanks a lot for the information. I am going to stop at Home Depot if I have time then on the way home! I will check Ramchargers website thought just to make sure. Thanks again!!

Thanks for the tech information. Ill try that when I get home. Thanks again

I just was wondering if anyone sells 4" MAF hoses for my MAF pipe. If at all possible it would be nice if they were blue but anything would help at this point. Thanks ahead of time!

I am going to have my car buffed in about a week. I would like to remove the Grand National badges along with the 3.8 SFI badge off of the hood. How would I do these safely without harming the paint? I heard a heat gun works but to be careful but I wasnt sure if there was a safer way to do it...

I am going to need the bushings for the upper and lower control arms. Would PST stock these? Brendan

I am going to bow my rear control arms myself. I was wondering if anyone sold just the bushing (hi-perf.) for these. Thanks Brendan

Which Way? This might be a really stupid question but when you cut the white wire does it matter which wire goes where from the spark advance or just connect the wires?

GM PARTS DIRECT I was just on their site and they said that they only have parts for Chevrolet at the moment. Am I doing something wrong or is the site down for the moment? Thanks Brendan

Gas Gauge Not Working I just got around to hooking up my battery the other night after having the car in storage for the past 1.5 years. I noticed that my gas gauge is not registering. I took my gas tank down and looked at the float and the wiring and everything seemed in tact as far as I know...