Search results

I tried a search, but not finding much info. So, what are the noisy chains vs quiet ones vs the ones that aren't worth a crap? Is there a timing set available that uses a tensioner? Is a Cloyes ok...saw the Rollmaster but quite pricey for a timing set. Thanks.

Hey Brian: Engine's at the Race Shop waiting for some back-ordered Probe pistons. What's this Texas address, not a GBGN anymore? I might have needed some parts from you!

Are the factory timing gears, chain, and tensioner still available? I tried to look up the parts using some part numbers I think were from GNTType org and got a "no match" on gmpartsdirect. Thanks.

200-4R vs 200-C I bought a G-force crossmember and plan to install a Rover/Buick aluminum V8 in the car eventually, unless my attention deficit kicks in (again.) I have the V8 parts except for a flexplate & an engine to trans adapter. What happens to the NA 3.8 and the 200-C? I have a few too...

Is the 200-C transmission the same length as the 200-4R? I am planning to swap a 200-4R into an 85 Regal that now has the 200-C and want to anticipate the need to swap or shorten the driveshaft. Thanks in advance, tp

Still got the rear sway bar and control arms?

I need a 200-4R dipstick and tube for a GN/TR or NA Regal. Prefer one that has low/no rust at lower end. Thanks.

Anyone who put in the biggie rear sway bar have a stock GN/TR one taking up space in your garage? I want one to put on the wife's NA 85 Regal. She loves the sofa-like ride, but when I drive it, the sway around corners is just too much! It borders on unsafe, and that's with a new set of shocks on...

Thanks. Thanks to all who replied or emailed me. I purchased one from a board member and got it in the mail yesterday.

I need a good, used, stock GN/TR balancer for my engine block that's at the machine shop. I prefer not to pull the one off the engine that's in my car now (it wouldn't be driveable if I did that!) Thanks, tp

I need to replace the wheel well chrome trim on the front & rear passenger side. Also in need of a chrome & blue hood ornament for an NA Regal that mounts on the header panel (all items going on a grandma fresh 1985 carbureted Regal that I just purchased for my wife. Car is in great shape, and...

Do you still have the right front fender?

I need a great looking 1986 TR burghundy 60/40 driver's side seat cloth (bottom and seat back.) Or better yet the material from an 86 burghundy rear seat (back and bottom.) I can have that cut and sewn to cover my worn out driver's seat. The 86 TR seat material seems to be different than the...

I need a great looking 1986 TR burghundy 60/40 driver's side seat cloth (bottom and seat back.) Or better yet the material from an 86 burghundy rear seat (back and bottom.) I can have that cut and sewn to cover my worn out driver's seat. The 86 TR seat material seems to be different than the...

Tell me I'm a winner I'll put the parts to good use!

Thanks! Just what I was looking for. I love this site. Great bunch of guys (as long as they aren't talking politics... things get kinda rough over there.)

Grumpy? Would you be willing to sell the one you have? Is it part # KB18213 ? The last one I had went with the TR engine I sold after a van demolished my 1985 Designer Series T-Type. Thanks for replies. TPolson

Does anyone have, or know who sells, the KB or similar oil booster plate? I would like an unused kit if possible. Or 2 if I can find them. They came with gaskets and springs. I am not looking for the longer gear kit, just the plate kit that was originally shown in the Power Source books.

I got parts yesterday, and they do look rather beefy. I am sure that the steering and handling will be more responsive when they are installed. The confusion over when they would get delivered was a bit of a hassle, but thankfully I was in no hurry. I just wanted to know for sure that they would...

I don't believe anything got shipped out by UPS, because it would be here by now. I got my $30 PayPal refund already, but no parts for the $369. Ya know, being honest isn't as hard as some people make it out to be. How many people have placed orders for this front end kit?