Search results

Just a reminder to mark your calenders for the Lucky Run in Bryan/College Station on January 10th, 2010. Kicks off around 8:00 am and continues till afternoon. There were a few Buicks that made the trip last year with the HBC. Usually around 300+ cars at this run, lots and lots of cool cars...

Pics of new cage built by disco stu. Anyone needing cage work done, I highly recomend him. .083 wall chromoly tubing, hand built, tig welded.

Thought I would share some pics of another part I've made. I made some adjustable lowers with heim joints on both ends (last pic), decided that it was a little too harsh of a ride and might be the cause of a false knock I've been incountering on launch. One of the problems I have is the...

Got a code 16 on XFI. In February I had a capacitor go out in my XFI ecu, sent to FAST to have repaired and borrowed a known good ecu to make sure there was not an issue with the car. I have had this borrowed ecu (thanks discostu) in my car since February without any issues (that I was aware...

Been running 17" wheels for the past few years and decided to dive in and get a new set of drag wheels. Went with the new Centerline competition series "Rev", new wheels for '09. Center Line Wheels I'm running F-body brakes, front and rear, front wheels clear no problem, had to modify the rear...

For those wanting/needing to replace the sloppy rag joint found in the steering shaft of the g-body: Found some info on a couple other g-body sites that a steering shaft out of a 1995 Jeep Grand Cherokee, which has u-joints rather than a rag joint, will swap DIRECTLY over to our g-body...

Looking for a working msd dis4 unit, would be nice to find the interface as well with it. Thanks Todd

Went a 10.96/126 on 93 oct./alky this past weekend. 24 lbs boost, horrible 1.78 60ft., 88* weather. I believe with a better 60 ft (launching off the t-brake) along with a little tweaking I should see some 10.7s or 8s. Either way I was happy to see 10s on pump gas. Many thanks to Discostu for...

would like to sell all together, but will seperate. combo price: $210.00 or: Accufab plenum- $175 RJC plate for accufab- $50.00 1/2" plenum spacer- $25.00 All are brand new and price includes shipping (paypal accepted) Thanks Todd

Excessive??? Nah, must have been a racer who designed it!!!

Took a few shots of my car over the weekend, thought I would share.

Circle D Specialties billet converter 3200 L/U single disc less than 2000 miles on converter Just got it back from Circle D, freshened up, cleaned, checked out, basically "new", excellent condition. Asking $550.00 shipped to lower 48, OBO Paypal accepted Thanks TK

Made a few j-rods after a few tb.com guys asked about them. Basically this is a direct replacement for the stock j-rod in the shifter (center consol shifted cars). When using a stage right trans brake, the stock piece can bend and end up going past 3rd gear (ending up in OD/N/R/P on the...

I'm going a different route with the car, decided to sell my converter: Cicle D Specialties billet converter 3200 L/U single disc less than 2000 miles on converter Just got it back from Circle D, freshened up, cleaned, checked out, basically "new". Asking $680.00 shipped to lower 48, OBO...

Got new wheels for my truck (tow rig) to go with the black theme I have on the GN. Think I should do the same on my car trailer? Or would it look a little too ....getto?

Went to a local Rod Run this past weekend, did a little exhibition burn out in the GN for kicks. Got a little loose, but fun non the less! YouTube - Lucky's Run (Preview)

On a freinds car (stocker), blew gaskets both sides #3 and #4 between cylinder and lifter valley about 6 months ago. thought last time it was a detonation issue, resolved/upgraded with inj upgrade, tt chip, cold air, coil module, alky control, Walbro pump, and downpipe. Car ran great. He...

Stepped up from a pt54 to a 6776 BB. Drove the car last night and noticed quite a bit of compressor surge even when I let off fairly easy. Any body else with a BB experience this? Normal? Also, should the internal wastegate be able to handle controlling boost (up to around 25lbs) with this...

Once again, I would like to say thanks to Holly and Cal Hartline for their support and knowledge in the Turbo Buick community. Ordered a new turbo from them and quizzed Cal (and Holly) about different stuff concerning a few tweaks on my XFI kit I recently purchased and which turbo to go with...

Is the front slip in yoke (1310) the same yoke for th350 trans? Need to get another, mine has started to twist. Looking at this one from Strange (Summit): Strange Super Duty Transmission Yokes: STR-U1661 - summitracing.com Thanks