Search results

I own a mostly original 87 t top GN. Car is in original condition now.. But its previous life I'm unsure of. True barn find, and the owner was very vague about past. Car has old school kenne bell ashtray switch panel, and front air scoop. There was an accident on passenger rear but seems...

This is a 2 part question.. Items totally unrelated. I can repost 2nd question in correct place if needed. #1. What is this? I received several boxes of parts when I purchased my car a few years back. Put them away.. But now I'm trying to clean out a little. I found 2 of these, still in...

Hey guys.. I have a question., and in sure the answer is somewhere on these threads, but I swear I've tried to find it ! Lol! Rubber or hard plastic filler neck bushing, washer... Etc. Any pieces between filler neck and valve cover is gone. Where can I find these pieces?? Also the cap and...

Any input, suggestions or advice appreciated! Proud owner of an 87GN for about the last 6yrs. All stock car to this point, had a ton of fun just enjoying the stock ride. Trans began giving issues, so I decided on a rebuild.. Now looking at a stall, and some more mods to make it MORE fun...

Just bringing my stock 87 GN out from winter storage. Spent the previous summer getting her in order and was able to put 3-500 miles in the car before putting it in the garage for the winter with no mechanical issues. The car was a blast to drive! After putting a few miles on the car this...

Dual gauge pod with water temp & fuel pressure gauges. fits on console, under radio. Brand new, never used. Purchased from Kirbans for $125... SELL FOR $100 SHIPPED! Also have an LT1 MAS $50 and a tilt stick for $20

Where could I find info/template for emblem location?

LT1 mass air meter $50 shipped Great condition tilt lever $20 shipped

Question for all the paint/body guys.. Just got my GN painted, and I have a few questions. After he attempted to buff it several times, I finally brought it home with a lot of what looks like a hologram on both sides. Can't really call them swirl marks.. What can clear this up for me? The...

****SOLD**** Good condition, plenum needs a good cleaning. $120 shipped

SOLD...$400. Nice used turbo.. Bought on a whim, and I'm gonna go in another direction. My loss is your gain.

Sold... 1 set of lug nuts. Black covers, and valve stems. Got an extra set laying around. New in box.. $40 shipping included. Pics upon request.

Replacing valve springs, and looking for suggestions. Stock car minus minimal bolt on pieces. NOT a race car. Seen the Kirbans, and heard the comps were "clicky" Suggestions appreciated. Thanks guys

****** SOLD*******Innovate wideband. O2 sensor was installed, but the unit was never hooked up. $170 plus shipping Driver side headlight bezel. No cracks, needs paint. $20 plus shipping Parking light trim, needs powdercoat $25 plus shipping Grille springs, new in plastic $15 plus shipping all...

Innovate motorsports LM2. Unit was installed on car I purchased, but to my knowledge was never used. Bung was installed, but the rest of the unit remained in the box which I still have. Assuming it is the basic unit, asking $220 and I will ship. Box, paperwork included. I DO NOT HAVE the cd...

Ok guys.. I have read a lot of posts referring to replacing bushings on the body/chassis.. most of which are negative toward the poly bushings. Can anyone shed some light on this for me? There are tons of options, OEM, energy suspension.. etc. AND btw.. My car is basically stock.. with a...

So I pull the car out of the garage & let it warm up a little.. cut the car off to use the trunk key (T-tops) now, the car wont crank back. With a little throttle, it'll start, but will not stay cranked at idle. Any clues? The car has a new fuel system, pump, walbro, pressure reg... HELP!

Not even sure this is the right forum.. but here it goes.. I am new to TB's, and after about 2-3 months of random reading and questions (thanks guys BTW) I have started my game plan. Now I have gotten to the turbo, AND my questions. Trying to decide on going with a larger unit, and I have...

GN newbie... So bear with me. Looking into getting the MAF translater.. just getting started on this project, and was noticing that the 3" sensor and the3.5" was basically the same price. Obviously bigger is better in some cases, but is that always the case? Like I said, new to GN, but I'm...

Looking a quality engine builder in eastern NC. New to the forum, and to turbo buicks in general. Any help would be appreciated