Search results

hey guys..I finished a complete on my 84 ...I sent the tranny out to get rebuilt at a local shop ...they seemed pretty competent and I was referred by many to this shop...long story short..it's been back there 3 times and it's only a little better than it was...I have a terrible issue with 2nd...

Hey guys..just wondering if anyone knows if there are more than one kind of lear seglar seats. I have an 84 gn and i ordered seat covers, but we are having terrible issues getting the covers to fit. They are definitely different than the ones i took off the seats as far as shape goes alot of...

Hi i am looking for an ls1 maf and translator in working order... have been having too many issues with finding a good stock type maf also will the ls1 maf fit in the stock location? thanks .mike

Hey there, ok so this is a fresh rebuild been driving it for 2 days now and have 55 miles on. Engine. The car Will not idle smooth sometimes stalls.. and taking off from dead stop or after a deceleration and getting back on the accelerator it 7 times out of 10 will stumble/miss. And then clear...

Whats the chance that a bad chime module would cause defogger,tail lamp, and instrument illumination fuses to blow? Out of the blue one by one they would blow. One blew replaced it turned on lights and the next one blew...reading the schematics thats the only thing they all have in common

.

/Ok so my sail panel windows have paint on the rubber trim around the glass the previous owner painted the car with the windows in and did a bad job with masking off. Now that I have re done the car completely I am getting ready to put the glass back in but I want to find a safe way to remove...

I tried to search this on here but came up empty on an exact answer, I have a set of fans out of an intrepid. I am trying to figure out the wiring on it, according to mitchell blacks are ground green is low and yellow is high, well green is the same speed as yellow but green and yellow...

hey guys so i am still putting the car back together and i have another extra plug. this one is on the drivers side it is a two prong plug with black and brown wires going to it it comes out of the light harness up near the drivers side head light..anyone have a clue what it is for?? thankyou...

Hey guys, so after the rebuild I have this part extra and can't figure where it plugs into under the dash please help!

Hey guys Ok so the the resto is getting close to being completed the issue i am having is getting the front clip aligned, anyone have any suggestions or tricks? or maybe someone has measurements from some reference points. thankyou in advance for the help Mike

Hey guys, ok so I have a freshly rebuilt 86 engine nothing fancy done to it just a rebuild with some beefing up to the bottom end, I have fuel pressure set properly and a new map sensor and new oxygen sensor the car fires right up and runs good but its very rich. Very stinky and when you rev it...

Hey guys, just wondering if anyone had experience with rebuilding window regulators, mainly the rollers that are worn out, i was able to locate the rollers from napa, i just wanted to see if anyone had any pointers on this task

there is a good chance someone already has a gauge kit out there and i have just missed it but if not a kit with all the important matching gauges would be fantastic, tach, water temp, trans temp, oil press, fuel press, knock gauge, boost, fuel/air mixture gauge, .. i would be very interested...

ok so just out of curiosity ..trying to wrap my head around fuel injection ...just for example say your fuel pressure was a little low for one reason or another the computer "should" pick up on this by the 02 readings being lean and its response is to try and leave the injectors open longer to...

i swear i have the worst luck searching in this site for things haha so im sure this is posted on here a few times i just cant seem to find the answers im looking for ok so i have a new rebuilt motor from the bottom up, 212,212 cam 50# injectors, .020 pistons , alky kit (not set up yet), rjc...

ok so i replaced my entire floor in the car and never measured where the hole was for the shifter cable to come up through the floor. Does anyone have there interior out of the there car and can measure up where abouts i should pop this hole? thanks alot

so I bought an RJC 3 inch downpipe and just installed it tonight. its slammed right up against the frame. . pinned so hard that laying under the car i cannot move it off the frame. any clue as to what is going on here?

Maybe this is on the site somewhere and I just missed. It ..if not maybe someone can explain the job the crank and cam sensors have. Imean I get the idea that this is how spark and fuel pulse are generated and timed. However it would be much easier to wrap my head around this if someone could...

Hey guys.. so Im doing some final fuel line connections and im having an issue with the O rings. I put the o rings on the ends of the lines and screw them together not rocket science right? well as i tighten the lines together it starts to feel funny so I take the line back off and the o ring...