Search results

NEED 2 GN CENTER CAPS WITH LOGO.

What fuel pressure sensor are you guys/girls running with a Powerlogger? Thanks for any information.

Has anyone ever been successful using windows 10 with a powerlogger. I had the owner of a IT company spend hours without success and his people do corporations. It was purchased new Oct 2017 and myself and 3 others, make that 4 now have failed at getting it to work. Are these things POS? I...

Had the instruction sheet and now can't find it, 2 questions does the gray wire go to the upper right or lower right on the PLX 4 pin receptacle (one is 0-1 volt the other is 0-5 volt, don't know which is which) and then the other end to the PL # 1 on terminal block. Thanks for any and all...

Looking for a known good working 40 pin to connect with a power logger.

The title says it all, good condition please.

LOOKING FOR 2 STEEL CENTER MAIN CAPS TO GO IN A 109 BLOCK. HOPEFULLY NEW, BUT USED IF THEY ARE IN GOOD CONDITION. THANKS

Some help from the guru's, please. Can I eliminate the S hose from the water pump to the intake without any issues arising? Can I eliminate the engine oil cooler system and there not be any problems? Next, putting in a hyd roller cam, lift is 0.516, how much should I have the machine shop fly...

Did a search and wasn't able to find the answer. I am trying to locate a wire for the tach signal to enable the lm2. Appreciate any help from you guys. Thanks again.

If I drop the oil pan will I be able to see the the timing chain tensioner? Not sure if there is one, believe the motor had a double roller installed and I'm now worried a tensioner may have been used with it. I read somewhere on TB the double roller will grind it up. Pulling the pan seems...

I have a sticker on the wastegate that reads, 430819-39 11224 17165 My question is it a HD or OEM replacement. Thanks all

Would one of you guys post a pic of your rear seat bracing? I had the back seat out and noticed the seams have split and seperated the caulk. Also do you think it helped from getting worse if you had the same thing occur as myself? Thanks Just trying to keep it together.

Considering the RJC boost controller which eliminates the solenoid, the puck is either 100% closed or 100% open at a predetermined boost pressure. Has anyone used this with success? Any thoughts or opinions would be appreciated. Here is the RJC description. Thanks Don...

I found some paperwork on my 87 GN that I have owned since 1995. It seems the car has a Kenne Bell MK1TXB EF 231 CAM (TURBO) and lifters KB10002 installed. I did a search to find the specs and his catalog but was unsuccessful, if anyone has information on this I sure would appreciate it. The car...

My 87 GN shifter cable has rubbed on the trans and now needs to be replaced. About 1 inch of the inner teflon liner is exposed (cut down the cable strands). Is there a vendor offering these or is fabbing a morse cable my only option. Has this happened to anyone else? Any input would really be...

Converter, 700-R4 / 200C / 200-4R *27 Spline, Igniter S/S 2800-3200 stall Code: PP7703 Price: $418.92 Quantity: 27 Spline, Clutch ommited, Size: 10, Bolt Pattern: 700-R4/350 , Engine: All Brazed Impeller: Y , Brazed Turbine: Y , Bearings: 3 , Washers: 0 , Notes: Unit does not...

Title says it all. Takes about 10-15 minutes to install. Everything plugs in, thats how it came from atr. One wire plugs into the o2 then the other wire plugs into what was pluged into the o2 to complete the circut. Then 1 wire 12v and 1 ground = 2 wires and 2 plug ins. The manual/instructions...

After being jerked around for 2 weeks here it is again. Who ever jrrusch is, do not respond! The price is $50.00 + shipping from 60462. It may weigh 7-8 lbs email fiveforty!@aol.com or call 708 403-5902 want pics send me your email i don't have paypal because i very rarely...

Complete working unit, with all the talk about how bad these systems are i decided to switch before any problems. $ 50.00 + shipping. It's a great deal just for parts alone.

Block has been maged, decked, align honed and bored 0.020 over. $540.00 in machining, processes done on a rottler. Will sacrifice for $500.oo ph, 708 403 5982 e-mail fiveforty1@aol.com located minutes from chicago