Pistons, Rods, Heads, roller rockers,etc.

[67turboCamaro]

Stage II alum. heads, full port by RSI, titanium valves and keepers, set up for roller cam.
-1 set fresh from machine shop, 240cc intake runners, 45 cc chambers.-$1500
-1 set used but in good condition, 240cc runners, 58cc chambers- $1200
Carrillo rods fresh from machine shop, -$700
Jessell roller rockers Like new dyno use only- $450
Stage II intakes, twisted style like new, -$50
Nascar style timing covers, Like new- $175
Roller cams for use with roller cam bearings- $100
14 bolt dry sump oil pans- $100
Carter mechanical fuel pumps- $30
MSD Pro billett distributors- $100
Bell housing to adapt Buick motor to Chevy manual trans.- $175
Light weight flywheels- MAKE OFFER
BOXES and BOXES of titanium valves-MAKE OFFER
1 Set NEW forged J&E pistons, 4.020, flat top- $500
1 set new J&E rings, 4.020- $100
1 set New forged Wiseco pistons, 3.95, flat top-$400
1 set NEW forged Wiseco pistons, 4.00, flat top- $400
1 Set New forged TRW pistons, 4.015, flat top- $400
1 set used forged TRW pistons, 4.010, flat top- $175
5 used forged Diamond pistons, 3.90, flat top- $125

All parts are + shipping
Serious offers considered. NO TIRE KICKERS PLEASE!!

 

[85HOT-T]

I am assuming that everything here is stageII

 

[rogerv6]

14 bolt dry sump oil pans

please send pics to roger@prtc.net

 

[67turboCamaro]

Originally posted by 85HOT-T
I am assuming that everything here is stageII

Mostly yes.

Roger, I will send you some pics tomorrow.

 

[85HOT-T]

Do you have any pistons for stage I, Thanks

 

[67turboCamaro]

All the pistons I have are listed. They will fit stock or stage blocks, depending on your bore.

 

[85HOT-T]

I am sorry but are those diamonds stock bore, if so what condition are they in.

 

[67turboCamaro]

Originally posted by 85HOT-T
I am sorry but are those diamonds stock bore, if so what condition are they in.

Nope, stock 3.8 bore is 3.800 and stock 4.1 bore is 3.985 (I think).

 

[fuzzyGN]

1 set NEW forged Wiseco pistons, 4.00, flat top- $400

What is the CH on these? Do they come with pins?

 

[CTX-SLPR]

Howdy,

How much for a set of 6 intake valves 1.745 or 1.775?

Thanks,

 

[67turboCamaro]

Originally posted by fuzzyGN
1 set NEW forged Wiseco pistons, 4.00, flat top- $400

What is the CH on these? Do they come with pins?

Compression height is 1.1985, and they include pins and locks.

 

[67turboCamaro]

Originally posted by CTX-SLPR
Howdy,

How much for a set of 6 intake valves 1.745 or 1.775?

Thanks,

I will have to check and see if I have any that size, and get back to you.

 

[fuzzyGN]

Compression height is 1.1985, and they include pins and locks.

Yikes, a bit short for my application. Thanks for checking.

 

[67turboCamaro]

Originally posted by CTX-SLPR
Howdy,

How much for a set of 6 intake valves 1.745 or 1.775?

Thanks,

Sorry, none that size. I have 2.10, 2.08, 1.65, 1.625, and 1.60.

 

[67turboCamaro]

TTT

 

[1radv6]

parts

im rebuilding my stock motor what parts do you have that will fit it? thanks

 

[67turboCamaro]

Head gaskets! $45 a set shipped. Everything else I have is stage II.

 

[buickstage II]

off center block?

im interested in the rods if there off- center style, do you have any other big end parts?

thanks Simon

 

[67turboCamaro]

Sorry, the rods are on-center. I have a couple cranks, but I am not sure which one I am going to use yet.