the Art Carr tranny is already sold . . . . . what's left?
Factory electric fan - $35
Hood trim - $20
Bumper filler support hardware (front and rear) - $20
Rear bumper fillers - plastic - $150
Front bumper fillers - fiberglass - $150
Rear 3 piece spoiler - $120
Factory std 109 block - $300
Rear deck lid (piece that goes in front of trunk lid) - $100
Front bumper - primered - $100
Front bumper support - $75
Rear bumper - $100
Rear bumper support - $75
Front head light supports - $20
Brand new Test pipe and hardware with cutout(for replacment of cat) - SOLD
Fuel tank - $150
Rear tail lights (good shape) - $150
Front grill - $55
Ps pump - $20
Starter - $20
Lower front spoiler - $40
practically new RJC stainless 3" down pipe - SOLD
Kenne Bell headers with crossover (v-band) -3 bolt - SOLD
Single shot exhaust dyno max muffler - $220
Newly assembled 109 block with forged TRW pistons - ARP main studs and ARP rod bolts. NOS block std crank std bore, never run - $1850
NOS timing cover - $150
NOS oil pump - $45
NOS balancer - $75
NOS flexplate - $75
Ported 8445 heads bare - $150
Intake with power plate (blasted, painted with all new hardware) - $175
PTE 6262 billet turbo fresh build with upgrades from Work Turbochagers. Upgraded supply and returns with filtered oil feed setup. - SOLD
Water pump - $35
Oil pan - $30
Chassis:
Brand new power logger with ECM - $175 -SOLD
Brand new MafT Pro setup with boost controller and solenoid. - $350
Art Carr 200R4 transmission fresh with 3000 NLU stall - SOLD
Factory rear in excellent condition - Royal purple gear oil - will come with roller unless it doesn't sell
Roller 1987 GN - clear and free title rust free!
Excellent interior with near mint condition seats
Tastefully added guages
Straight body sanded and ready for paint - can spray epoxy primer if requested.
$4000 negotiable. May include items above with negotiation.
I will wait to sell body parts until I see where we are with the roller. If i get no serious inquiries with a week or so then the roller is getting parted out as well.
Shipping is NOT included especially on cheap stuff. I will accept offers but nothing rediculous.
Thanks,
Brian
PARTS I FORGOT ABOUT -
Intercooler (soda blasted and painted silver with bare alu core) -$75
valve covers bare - $30
valve covers painted -$40
Good Coil with ICM - $80
custom 4" air intake with filter - $50
accessory bracket with pulleys and tensioner - $80
Factory electric fan - $35
Hood trim - $20
Bumper filler support hardware (front and rear) - $20
Rear bumper fillers - plastic - $150
Front bumper fillers - fiberglass - $150
Rear 3 piece spoiler - $120
Factory std 109 block - $300
Rear deck lid (piece that goes in front of trunk lid) - $100
Front bumper - primered - $100
Front bumper support - $75
Rear bumper - $100
Rear bumper support - $75
Front head light supports - $20
Brand new Test pipe and hardware with cutout(for replacment of cat) - SOLD
Fuel tank - $150
Rear tail lights (good shape) - $150
Front grill - $55
Ps pump - $20
Starter - $20
Lower front spoiler - $40
practically new RJC stainless 3" down pipe - SOLD
Kenne Bell headers with crossover (v-band) -3 bolt - SOLD
Single shot exhaust dyno max muffler - $220
Newly assembled 109 block with forged TRW pistons - ARP main studs and ARP rod bolts. NOS block std crank std bore, never run - $1850
NOS timing cover - $150
NOS oil pump - $45
NOS balancer - $75
NOS flexplate - $75
Ported 8445 heads bare - $150
Intake with power plate (blasted, painted with all new hardware) - $175
PTE 6262 billet turbo fresh build with upgrades from Work Turbochagers. Upgraded supply and returns with filtered oil feed setup. - SOLD
Water pump - $35
Oil pan - $30
Chassis:
Brand new power logger with ECM - $175 -SOLD
Brand new MafT Pro setup with boost controller and solenoid. - $350
Art Carr 200R4 transmission fresh with 3000 NLU stall - SOLD
Factory rear in excellent condition - Royal purple gear oil - will come with roller unless it doesn't sell
Roller 1987 GN - clear and free title rust free!
Excellent interior with near mint condition seats
Tastefully added guages
Straight body sanded and ready for paint - can spray epoxy primer if requested.
$4000 negotiable. May include items above with negotiation.
I will wait to sell body parts until I see where we are with the roller. If i get no serious inquiries with a week or so then the roller is getting parted out as well.
Shipping is NOT included especially on cheap stuff. I will accept offers but nothing rediculous.
Thanks,
Brian
PARTS I FORGOT ABOUT -
Intercooler (soda blasted and painted silver with bare alu core) -$75
valve covers bare - $30
valve covers painted -$40
Good Coil with ICM - $80
custom 4" air intake with filter - $50
accessory bracket with pulleys and tensioner - $80
