Search results

Well I just got through with installing my new alky control kit, tested out the system which worked just fine. Took the car out for some more tests. I started out with 17 psi without akly running fresh 93 octane and I would see barley any knock retard on my scanmaster. I made incremental...

Im looking for a replacement for my factory hard metal vacuum lines that connect to the top of the intake near the throttle body. Does anyone reproduce these?

The 4th Annual UMass Motorsport Spring Car Show and BBQ Sponsored in conjunction with SWAG: Southwest Area Government SouthWest Week and ASME: American Society of Mechanical Engineers Go Fast or Go Home! Saturday May 1st 2010 Rain or Shine Event Summary: This show is the grand finale...

For Sale: 1987 Buick Regal Grand National Astro Roof Engine: Stock 3.8L Turbo V6 Mileage: 110,000 Full Description: This car has gone through a mild restoration since I aquired this car. Always garage kept. The body is 95% rust free. There is a small rust buble on the trunk lid lower...

Looking for a good used alky kit.

I'm looking for a set of 60lbs injectors with a turbo tweak chip setup for alky. Thanks

Does anyone here know how the front bumper molding attaches to the bumper? Is there certain clips I need to get? If so, from where?

I recently finished installing a new timing chain on my 87. I also ordered a new cam sensor cap from Casper. I followed the directions on setting it. The car does start up, but when I took it for a ride, as soon as I gave it quarter to half throttle it started to hessitate and skip bad with a...

I'm looking for the 4 or maybe 5 bolts that hold up the torque converter cover to the tranny. I can't find replacments anywhere. Eric

This weekend I replaced my worn out timing chain, and after putting it all back together i'm not getting any spark. Here is what I did. Replaced chain and gears at TDC. Dots aligned top to bottom. installed crank sensor and set gap correctly. Installed cam sensor with new Casper sensor...

I don't have an oil cooler, so how can i correctly prime the oil pump?

For some reason my gn's radio goes to static once every few minutes. I just found out that when that happens all i have to do is turn on the AC and the static goes away for another 3 minutes or so. Any ideas on this???

Anyone know what size bolts are used to hold the TC cover on my 87 GN?

Looking for a used but good condition Razor Alky kit for my 87 GN

For some reason, my 87 GN starts to hesitate and miss after I drive the car for about 10 - 15 min, then shut off the car for 5 then restart it. After i restart it, it begins to hesitate when i barely touch the gas. I replaced the coil and ignition module and the same thing happens. My last...

I'm searched high and low, but can't get a difinite answer to my question. I just for 4 black gta rims. 2 Front, and 2 Rear. I'm planning on putting the "fronts" on the rear of my GN, and the "Rears" on the front. I understand i will need a small spacer for the "rear" wheels to fit up front. My...

I may pick up a set of doors from and 87 cutlass 2 door. These doors have side moldings down the middle of the door and a wide chrome molding on the lower portion of the dooe. My question is, are these just glued on or are there holes drilled in the door for them to be mounted? I'm hoping i...

Selling 4 GN rims on decent shape. They have some curb rash on them and two have small dents on the lip, but can be hammered out. They are mounted and balanced on 4 BFG radial TA tires. Size 225 60 15 for the fronts and 245 60 16 in the rears. Two tires are brand new, and they other two still...

Selling the factory oil cooler with lines out of my 87 gn. Has 109k on it. Works great. $40+ shipping PM me

Can anyone tell me what cars have the same ignition control module as my 87 GN? And if i can also find a mass air meter out there too for testing purposes? thanks, Eric