Recent content by Buickcruiser

I have XP Pro. I have clicked my computer then the cd drive and i see an icon that says install. it takes me to dos and says do you want to install i push y and it take me to another screen that says pick your dive I then Click C and the dos screen goes away?????? Thanks David

I have XP Pro. I have clicked my computer then the cd drive and i see an icon that says install. it takes me to dos and says do you want to install i push y and it take me to another screen that says pick your dive I then Click C and the dos screen goes away?????? Thanks David

Hey Guys, I am reposing this here also because of lack of responses in the scan tool section. How can I install the Turbolink V2.13 onto my new laptop (no floppy drive). I have a scan disk and have transferred all of the Info from the disk to that, but when put the scan disk into my computer...

Hey Guys, How can I install the Turbolink V2.13 onto my new laptop (no floppy drive). I have a scan disk and have transferred all of the Info from the disk to that, but when put the scan disk into my computer at startup it does not automatically download like it is supposed to according to the...

Hey Guy’s Advanced finally got the plug wires in. Installed them along with new ac 43ts plugs and new positive battery cable and crank and it fired right up. :D It’s running great. I will hook up and adjust the iac and tps on Monday bc I have to go out of town this weekend. But just wanted to...

Hey guys Got back in town and checked all of the wires. I noticed that the positive battery cable was frayed at the bottom and was very close to grounding. I bought a new wire and attempted to start and the car sounded a lot stronger but would not start. Pulled a pug and it was covered in...

Hey Guys I am heading out of town in a few. But I will be back Saturday and check all of the ground wires. I’ll let you know how it turns out. Thanks Again David

Hey Boost231 Ok on my lunch I went home and hooked up the turbolink. I am getting .48 with foot off pedal and 4.48 all the way down with the mat out. I know this is not right where they are supposed to be but it’s not that far off. Would that little .02-.07 affect the car that much? I also...

87gta-turbo Also I had a question about the MAF it was 1st run 20-30 second 18-25 3rd a constant 15. I turned the fp up and now the car won’t start. If you could take a look at the hot air section and if you have any suggestions it would be greatly appreciated...

OK Brad do you mean that it should have 13-14 with the engine off??? I am about 12.45 with the engine off. I pulled the battery last night and took it to advance and they said that it was fine and it didn’t even need charged. I put it back in and was able to start it for about a second or...

Hey guys Ok I turned the fuel pressure up and the car started to smooth out some. I then shut it off to grab some dinner and came back out to adjust the TPS and the IAC, but it won’t start (It will crank but not start:confused: ). You were correct in noticing that the voltage was low at 11.7...

Hello Guys I have done the following upgrades because of a blown head gasket. oversized t.b. new valve springs, adj. Fuel pressure regulator, . adj. wastegate, 86/87 ECM, Turbotweek chip, Turbolink, hooker exhaust w dump pipe, Welbro 307 Fuel pump w/ Hot wire kit and 50 lb.injectors and ported...

Hello Guys I have done the following upgrades because of a blown head gasket. oversized t.b. new valve springs, adj. Fuel pressure regulator, . adj. wastegate, 86/87 ECM, Turbotweek chip, Turbolink, hooker exhaust w dump pipe, Welbro 307 Fuel pump w/ Hot wire kit and 50 lb.injectors and ported...

Ok at set at 10 ADC i am getting 0.00 at 200madc I get 6.6 is this normal? Thanks David

Hey Guys, I finally got my car running (its running a little shaky and the vac is high) after a few installs. Which oversized t.b. electric fan, new valve springs, adj. Fuel pressure regulator, Trans cooler. 86/87 ECM, Turbotweek chip, hooker exhaust w dump pipe, Welbro 307 Fuel pump w/ Hot...