Stretch inter cooler

[jim0207]

I got this IC back in the 90s. No scope or brackets. Vary well built. Inlet and outlet fit my 87 GN. But, no brackets or scope . So I now going to sell it. I do not fabricate. The passenger side top mounting hole is 2" horizontal from the edge of the core and the cross hair , or vertical measurement is, to the top hole is 3 1/4" down from the top of the core. It has not been pressure tested. First to say I'll take it, takes it. The IC has:

2" inlet and outlet
3 1/2" manifolds
23 tubes at 1/4" thick
Core is 13" wide and 14 3/4" tall

$395.00 OBO

 

[TBlaze]

Looks to be a nice Tony Dequick CASv4. Good luck with your sale.

 

[we4Mateo]

I thought it was a CAS V4 too but it'd have 2.5" in and out if it was. That pass side bracket and the long bolt that goes into the waterpump will be needed but I'm sure it could be fabbed up too. GLWS! Very nice intercooler.

 

[Justa_v6]

Interested, trying to find a shroud for it.


Does a regular stretch intercooler shroud fit?


Posted from the TurboBuick.Com mobile app

 

[87_we4]

Looks just like my cas v4. Except I have 2 1/2 inlets and outlets. Glws

Posted from the TurboBuick.Com mobile app

 

[Justa_v6]

Looks just like my cas v4. Except I have 2 1/2 inlets and outlets. Glws

Posted from the TurboBuick.Com mobile app

What type of brackets did you use with your intercooler?


Posted from the TurboBuick.Com mobile app

 

[Justa_v6]

Has this been pressure tested?


Posted from the TurboBuick.Com mobile app

 

[we4Mateo]

What type of brackets did you use with your intercooler?


Posted from the TurboBuick.Com mobile app

There is a specific pass side bracket for this ic and the stock driver side bracket is reused.

 

[TBlaze]

The 2-1/2" is on the OD, the ID measures some 2.1", stock measures under 2.1" on the OD and the ID around 1-3/4" I would suspect the 2-1/2" on the OD is correct. Precision is the only slic that I know of with 3" in and out. Hope that helps.

 

[Justa_v6]

It has no leaks right?

Trying to locate a passenger side bracket and shroud I will respond shortly via pm


Posted from the TurboBuick.Com mobile app

 

[Justa_v6]

Going to pass on intercooler
Sent a pm


Posted from the TurboBuick.Com mobile app

 

[Dreamcar86]

Interested, trying to find a shroud for it.


Does a regular stretch intercooler shroud fit?


Posted from the TurboBuick.Com mobile app

I have a shroud as I destroyed my V4.

Posted from the TurboBuick.Com mobile app

 

[Dreamcar86]

There is a specific pass side bracket for this ic and the stock driver side bracket is reused.

I have the bracket as well.

Posted from the TurboBuick.Com mobile app

 

[Dreamcar86]

May have all the hardware.

Posted from the TurboBuick.Com mobile app

 

[Justa_v6]

Can you PM me pics of everything


Posted from the TurboBuick.Com mobile app

 

[Dreamcar86]

Can you PM me pics of everything


Posted from the TurboBuick.Com mobile app

Yes, let me find it in the attic and I will do that.

Sent from my SCH-S738C using TurboBuick Mobile mobile app

 

[bpman1234]

dreamcar do you still have the shroud ifso can you send pics please.thanks eddiedawg123@aol.com