TURBOPOWERED68
David
- Joined
- Jan 31, 2006
LI, NY
$5500.00 takes it all -- Engine and listed stuff only.
The long block was Built by David Husek.
Everything is on the car and working/running the cars best is 11.74 old combo, the new combo only went 11.95 on a bad trans and NO Tuning.
if i was to part it out, it would look like this
I will only part it if i can get a good amount of the stuff sold - If interested in a part post up.
1- 11k miles short block with 20 over trw forged, stock rods, stock crank i THINK it is std/std
2- Stock Iron heads with bigger valves --RPE did the Valve work and springs for a roller cam, bowl work and a little clean up by someone else ????.
3- HR 1.65 Roller Rockers a few months old, had to grind them to make them fit- about 300 miles on them.
4- 206/206 billet webber roller cam with hardware.
5- Morell roller lifters
6- Roll Master timing chain
7- Timing cover - not an Earl unit but works great- oil pressure is 25-30 HOT
8- Stock lower intake manifold
9- Stock Throttle body Ported to 62mm with matching plenum by Steve Monroe
10- RJC Power Plate for stock plenum and intake
11- Scanmaster with PL update ---- $190.00
12- PowerLogger
13- BB 2-Step with brake pedal switch
14- Coil and Module -- on car working.
15- MSD 8mm red wires
16- Hacked up engine harness, replaced ECM, Maf plugs and it shortened --its working great so far.
17- Stock intercooler fan
18- Stock intercooler
19- Stock MAF sensor - Working
20- Power steering pump and reserve with backwards thread cap
21- Accessory bracket -- Welded 7 years ago works great.
22- Ac Delete pulley with bracket
23- Aluminum plenum Spacer 1 inch with some Vacuums on it.
24- Adjustable fuel pressure regulator
25- Volt Booster Reds
26- Damper
27- Flywheel
Ask for other under the hood stuff that i might have forgotten
$5500.00 takes it all -- Engine and listed stuff only.
The long block was Built by David Husek.
Everything is on the car and working/running the cars best is 11.74 old combo, the new combo only went 11.95 on a bad trans and NO Tuning.
if i was to part it out, it would look like this
I will only part it if i can get a good amount of the stuff sold - If interested in a part post up.
1- 11k miles short block with 20 over trw forged, stock rods, stock crank i THINK it is std/std
2- Stock Iron heads with bigger valves --RPE did the Valve work and springs for a roller cam, bowl work and a little clean up by someone else ????.
3- HR 1.65 Roller Rockers a few months old, had to grind them to make them fit- about 300 miles on them.
4- 206/206 billet webber roller cam with hardware.
5- Morell roller lifters
6- Roll Master timing chain
7- Timing cover - not an Earl unit but works great- oil pressure is 25-30 HOT
8- Stock lower intake manifold
9- Stock Throttle body Ported to 62mm with matching plenum by Steve Monroe
10- RJC Power Plate for stock plenum and intake
11- Scanmaster with PL update ---- $190.00
12- PowerLogger
13- BB 2-Step with brake pedal switch
14- Coil and Module -- on car working.
15- MSD 8mm red wires
16- Hacked up engine harness, replaced ECM, Maf plugs and it shortened --its working great so far.
17- Stock intercooler fan
18- Stock intercooler
19- Stock MAF sensor - Working
20- Power steering pump and reserve with backwards thread cap
21- Accessory bracket -- Welded 7 years ago works great.
22- Ac Delete pulley with bracket
23- Aluminum plenum Spacer 1 inch with some Vacuums on it.
24- Adjustable fuel pressure regulator
25- Volt Booster Reds
26- Damper
27- Flywheel
Ask for other under the hood stuff that i might have forgotten
Last edited:
