Search results

I doubt this would work. IMO

HI everyone , I am always looking for some good logs to go over, and give some tips. Send them over with some info on the car. Advice is always free:) Or msg me on FB to discuss them. Only one Norbs with XFI avatar on FB that i Know of.

Do not forget to change the comport speeds in device manager under the serial ports advanced tab to 64 bytes for TX 64 bytes for RX latency to 2 Or it will communicate slowly , and your logs will have very little data frames.

Hi erveryone, I have this up on the FB XFI group but I have decided to post it also as it can pertain to all types of ECU's on the market. I feel its important to all the buick members, so here it is. The motor must be in reasonable condition, no weak cyls. The battery must not be weak or...

Selling for a friend buick steering wheel that came from a non turbo regal. It is the same wheel as a gn or ttype just the center cap is different. Reasonable condition i would say a 7 out of 10. See pics $220 USD. But could be a bit flexible on price.

Looking for a champion on center intake for GN-1 heads for a friend.

Hi I am upgrading a car so I have some parts left over. Everything was working upon removal. Fast 95 lb low imp injectors approx 6000 miles on them, nice shape FASt CLassic ECU with precision Buick adapter harness ( not caspers harness) Used wideband sensor lil rough shape on wrenching...

Selling stock lower intake in good shape egr tower removed and filled in.It has been port matched but not hogged out, also will include 70mm polished precision plenum $275 usd for both...Intake has never been milled, no striped bolts no, porting past gasket lines, NO HACK....... Attached...

Due to financial difficulties I am forced to sell my set of M&A heads. They are machined and I can include multiple sets of valve springs. However they have 1.94 intake valves and will not fit on a 3.8 bore. They heads were cracked and have been professionally repaired, and re-tested with no...

Looking for a 4" bore piston set, for 6.3 rod to work with 3.625 or 3.59 crank set up.

Complete B2B Fast with buick adapter harness, and new WBO2, no map sensor or serial cable $700 Cdn Plus shipping. Will supply a startup program for your needs....

The issue with the 1500 RPM spike ant 100% duty cycle effects many buick users, and is a mystery why it can;t be sovlved. Can Fast please make a software patch that limits the injector duty cycle when in start mode (under 400 RPM)..

There seems to be a lot of people logging items that should be logged and they are not. The XFI can log 24 sensors max, if you go higher than 24 the next sensors will not display properly. It does not slow anything down if you log 1 or 24 sensors, like in the classic after 14 sensors the...

Hi for those who don;t have anything to start out with here is a program, that should get you up and running, its very basic, and will require tweaking.

I have been fooling around with BS3 and its logging, as it has many nice parameters the interface is not to my liking at all. This makes me say I will never own a BS3 , and makes me like FAST XFI even more...I can;t even make an improvement list for its too over whelming..

Hi, this is a street program for those who need to get the car up and running, cold start is flawless. Set up for GN1 heads and 218 cam on a 272 ci motor, 71 gtq, headers 93 octane fuel. However if you have a similar build just change the cubic inch size. This has not been tuned over 10 psi so...

There has been a lot of talk on this forum about knock retard and the mysteries associated with it. 1st of all I would like to thank Dennis Leek for contributing the stock ecu knock information that I am about to discuss. To sum up the stock ecu infomation we have to think mentally what is going...

Hi looking for a way to plug off the kickdown terminal switch on the trans. Does anyone make billet blank plug for this to seal it off?

Ok here is the start of the list of suggestions I have come up with so far. 1. The fixed position gauges must go, they should be able to be hidden, parameters selected and sized by the user. The select colours should not be picked using html colour codes, that is crap. 2. The spark, A/f table...

Hi if you wanted to log your fuel pump voltage for example with your XFI, but you only have a 5 volt input you need to build a voltage divider network, and connect to your analog inputs to lets say 16 volts in =5volts out You can use the following online tool to build this...