Search results

Does anyone have a set laying around? Are any other vehicles interchangeable that I can use? May consider a complete set of bushings if you have them available.

Anyone have a performance set of lowering springs for an 87 Turbo T?

Located in Colorado Springs, CO. $14,700 150K miles on the odo. Recent 12” LS1 brakes and new hydro-boost unit. New Kuhomo Ecsta Sports tires, Rev 100 wheels (17*7 and 17*9), MSD 50lb injectors, Turbo Tweak chip, PTS trans parts, re-stalled 12" converter, and a GT-3255 turbo from...

I am removing my Biggie Oil filter kit and I need the stock oil filter adapter piece that holds the oil cooler adapter in place.

I am in need of a speedometer housing complete, for my transmission going into the 442.

Looking for 200R4 parts, floor shift. I could use the cable bracket on the transmission pan and the complete speedometer gear housing.

My AC compressor has finally failed after 130K miles. Looking for most if not all of the AC parts. Let me know what you have.

Does anyone live in or around this this city? I saw a 83 Hurst Oldsmobile for sale and was wondering if someone could check it out for me. I can compensate you for your time ebay Item number: 150347347593 Oldsmobile : 442:eBay Motors (item 150347347593 end time Jun-01-09 11:55:56 PDT)...

I have the following Parts for sale VDO Gauges: All 2 1/16, Tachometer $35, Temperature, no sender $20, Boost, bezel needs re–painted $15 Autometer 2 5/8’s Phantom Boost gauge, nice $30 A gray pillar pod single 2 5/8, $20 or $40 with Phantom boost gauge Kenne Bell Hood Mounted FP gauge...

I am looking for an up pipe drilled and/or with a Razor ALKY nozzle ready to go. Thanks

Looking for suggestions on how to have this reproduced or make one myself. Can anyone trace or already have a diagram so I could compare it to my completed housing measurement then cut it from a piece of clear plastic or Lexan? Thanks

Looking to purchase a AEM wideband? Thanks, Lance

Has anyone in this area seen this Hurst? Would someone be willing to go check it out for me, I would be open to making it worth your time. eBay Motors: Oldsmobile : Hurst/Olds (item 260287991056 end time Sep-21-08 21:08:05 PDT) Regards, Lance

I am looking for a 83 Hurst Olds, or leads on one. I would like to buy one from a fellow enthusiast and it does not have to be in running condition, but would prefer mostly complete. Might consider a 1984. I am located in Colorado Springs, CO. Regards, Lance BB_OLDS@msn.com

Looking to get $35.00 shipped. It will come with hoses and clamps.

I am looking for a triple pillar pod that replaces the factory trim. If it is blue all the better.

My fuel line is cracked & leaking right near the cross member where the clamp secures it to the frame. I had the cross member down and may have banged up the line some putting it back in. Can this line be replaced with minimal hassle? Can it be snaked out of the front frame/ engine...

Well I am about to finish installing a GT3255 on my car and the new waste gate actuator (from Precision) is to long in relation to the swing arm. It is adjusted as short as possible and still about a 1/8th inch in front of the puck arm. Do I need to shorten the threaded arm some by trimming it...

I am in the middle of replacing my timing chain and valve springs and noticed a bracket that clips on to the fuel lines and looks to hold them against the water pump. However mine was not attached anything and slid to the bottom of the lines. I am looking for advice on were it attaches...

I am considering to replace my stock intercooler with a larger stock location intercooler & down pipe/ported elbow to support a turbo upgrade. I have several WTB out there so if you replied already I still have all the offers and thank you.