Search results

For sale, stock intercooler, standard inlet and outlet, out of my 87 Turbo T, pics furnished upon request, great condition, $100 firm, buyer pays shipping charges

I have a stock intercooler for sale, its in good condition, Stock inlet and outlet, intercooler only, pic upon request, $100 firm, buyer pays freight. I am located near Little Rock AR. Shipping would probably be from zip 72209. Thanks:)

Anybody got a good source for weatherstrip that won't break the bank? I looked at Kirbans and SoftSeal. SoftSeal's prices ran about $350 for the set best I could tell, Kirbans was even more than that. Any other sources anyone would like to share. Its for a 87 Turbo T with WE4 trim. Thanks; Robert

This is the relay that runs the electric fan for a period of time if the motor reached temperature and was shutdown. Anybody know where I can get one or is there something that is being substituted.

Any one got any idea what size and thread the two screws that are used to hold down the back of the shifter trim plate on top of the center console. Looks like there is something to screw into off the console itself underneath the trim plate. Thanks

TE44 For Sale, less then 1500 miles on it since rebuild. New Precision exhaust housing added when rebuilt. Rebuild by John Craig/Limit Engineering. Price is $350.00 firm, you pay shipping cost. Pics hopefully added this weekend.

Anybody know offhand the size of the studs. I need to buy something to chase the stud threads as well as some new stud nuts. Thanks; RBruton

I am installing a TA62 and curious if anyone had the O.D. on the stock intercooler connections as well as the stock throttle body diameter. The turbo inlet appears to be 3" O.D. and the outlet appears to be 2". I am looking at trying to order a few connecters that fit alittle better and are...

I'm throwing this out there to see if any have any suggestions. I'm running into a lean situation with the following readings on my scanmaster. After the motor has gone into closed loop the INT is reading 128, the BL is 150 and the IAC is 00(these readings are steady). The TPS is set at .44. I...

Does anybody know if the small filter on the back side of this unit under the round cap is available from anyone? I assume worst case I can just stick some sort of filter foam on it. I was pulling it off and it tore apart and crumbled(guess it had been on there a long time)

Anybody know if the coil on the 87 Buick was used on any other vehicles. I need to replace a coil-pak gasket that I borrowed from a friend when looking for a problem that turned out to be something else. I know I can get it from any number of businesses that specialize in the Buicks however that...

Thought I would throw this out there for comments. Car was running fine, hit it pretty hard out on the freeway, got to the house and car was running very rough at idle but seemed fine out on the highway. At idle it was very rough and spitting out some black emissions. Didn't have time to mess...

This is the only bolt I seem to be missing from my fix-it project. Does anybody have a clue the size of this bolt. Can't find any help from the local parts stores cause they say its an original part and they have no parts list for it. I have tried a search without any luck.

Can anyone advise the tightening sequence that will help get the best seal so I don't have to replace any head gaskets for a while. I am installing ARP studs and nuts, haven't looked but been told there are 3 different lengths(don't at this point have a clue how the different lengths apply)...

I have stock heads. I have purchased ARP studs and nuts and want to run the holes with a thread chaser but have not been able to specifically pin down the size of the studs. The box is not specific, ordered from Summit and their info is not specific, tried calling and couldn't hang on that long...

Went to the dragstrip for first time this year without proper tools and messed up my rear wheel lugs. I'm running the extra long studs that have the stock metric thread and using a stock Turbo T aluminum wheel for my slicks. I believe the lug is a 13/16" but wanted confirmation on what the...

Recently had a B & M Launch Control installed(line lock) and its not holding weren't a dern. I tried new shoes on the front but they didn't improve the situation. Basically it will not hold the car even if I overpower the rear brakes and get them to spinning. I contacted Summit and got the...

Was wondering if anyone has experience with using a Dunlop GT Qualifier 295/50R15 on the rear. I am trying to stay in the street legal radial class which must have a hardness or treadwear of 200 or more. The Dunlop fits the bill but this tire requires at least an 8" rim and will require...

I have a 87 WE4 that was painted about 4 years ago. I have only had the car about 7 months. Based on some of the posts it appears there are quite a few opinions on the color black. The paint on this car is not originally and is black as it can be with no tinting that I can tell. I need to touch...

I was advised by another Buick owner that a gasket is available from parts stores for this location but you have to ask for a turbo to exhaust manifold gasket for Buick Riveria somewhere between 1984 to 1988. Can anyone pin it down to what year I need to ask for?