Search results

Thank you, I believe it is definitely the cam. I pulled the valve covers today and one rocker arm is moving about a 1/4 of normal travel and two others are at about 1/2 travel. I appreciate the help from everyone to narrow this down. As much as I didn't want this to be the problem, at least...

Thanks

Thanks to you both. So what is the popular cam these days. Should I go roller. Are they now reliable? I'll take any suggestions. Any suggestions on a shop in the Maryland area to do this work? The car has ported stock heads, bigger valves, TE60, bigger downpipe, etc. Thanks for any advice.

It is a Reed Cams 210/205 circa 1998. It has been in there since then and has about 30,000 miles at most. As far as testing it, I don't have a dial indicator so other than pulling the valve covers and watching the rocker arms I wouldn't know. Could this also be a bent pushrod? Thanks

I was driving around one night and the car was running fine under boost. Later the same night while still driving the next time I got on the boost I had severe detonation over 10 Psi. I have been troubleshooting for a couple weeks now when I have had time and the problem seems to be getting...

Thank you.

I currently have a 210/205 cam, ported stock heads, bigger than stock valves, TE-61, 24 lbs. of boost with alky, rjc plate, ported intake, bigger throttle body(stock ported and new blade not sure how big), 3.42 gears, and a front mount intercooler. I currently run blue tops with the adjustable...

What kind of injectors are they? High/Low impedance? Size?

Thanks for asking to see more. I enjoy looking at everyones Limiteds as well.

Thanks, I spent many, many hours wet sanding and buffing after a paint job.

maryland silver Here's mine.

Do you still have the stock crossover pipe for sale?

Looking for chrome/aluminum wheel well molding I am interested in chrome/aluminum undented wheel well moldings for each wheel well. Also looking for the 3 pc. chrome/aluminum rear window trim. Do you have this? How much?

I have looked through the threads, but can't find an exact answer on this issue. I want to put a 17x8 up front with a 3.5 in. backspacing with 245/45/17. Will it rub? Will a 4.5in. backspacing wheel in a 17 rub less? Thanks for any help!

I have a semi-bad lifter. It seems to be OK most of the time, but usually after I run the car hard it taps loudly for a few seconds. After that it is usually fine with no audible problem. I just put in a oil pressure gauge and pressure is at 40 psi when above idle and cruising, but it is at 10...

I think I have the same problem Does your miss occur at around 50-60 mph with the tach at around 1800-2200. This is driving me crazy with the missing and bucking. I changed the coilpack, ignition module, and put on the 10 mm wires from Magnecor. The problem was fine for a day, then it came...

Did you figure it out yet??? I have the same problem but I just had my head gaskets replaced last week and the problem is still there. I changed coil pack, ignition module and wires all at the same time and it solved the problem for a day. I am not using the metal spark plug boot from the...

Did you figure it out yet??? I have had the exact same problem for a while now. I have replaced the coil pack, ignition module, wires, etc.. When I changed all three of these at the same time, it was great for about a day. Then the next day it was back again. Uhhh!! The car runs great other...

Thanks, for all the info. I appreciate it. I guess I will be pulling the intake manifold this week. Oh well, I guess it could be worse. Thanks again.

Not a good thing I took off the passenger side valve cover today and found a rocker arm shaft broken in half. No problem it was an aftermarket and I still had the GM unit at the house. That was until I tried to put the push rod back onto the lifter it fell off of. I can't find it. It's almost...