Search results

Nice :D

Thanks!

Still taking deposits for this? I need a tensioner :(

Does something need to be turned on in .bin for the Scanmaster to work? Mine powers on, then goes blank. I have a diode running to ground, the resistor going to +12v, and they both connect to the wire Scanmaster signal wire, that runs to D2 on the ECM....I suck at reading schematics, but...

That would probably work. Superglue would probably destroy it.

Who makes a good MAFless CAI? My temp. air cleaner setup is pretty crappy looking, lol. https://www.dropbox.com/s/jnspm1hx967zguw/IMG_20150519_135004.jpg?dl=0 Spark plugs look a lot better. One on the left are my plugs from the old ECM...

This setup is pretty impressive once everything is wired up right. I dont think my car has ever idled this nicely. :D

Trying to run closed loop. The only place I noticed any knock counts was when I shut the car off, to flash the new .bin after some learnin'. I didn't catch any knock other than that, I'm watching the log over again though. Even at startup, my Caspers knock sensor never went off. Not sure if...

https://www.dropbox.com/s/byyrir9foy81guj/5.dat?dl=0 Went a couple miles, seems to run very well. Idle still a tad bit rough. Pretty happy.

Can't wait till I get it out for a few quick cruises.:)

https://www.dropbox.com/s/n8crj2itk5t06vq/2.dat?dl=0 Grabbed one quick before I left, the German Sheps aren't eager for the vets anyways ;) BLMs are getting better. Knock seems to be there on start up, or when it goes into Closed loop idle. Thanks guys! Be back in a bit.

Adjusted the IAC a little more, and it started learning. I was recording a log, but windows updates figured it was more important and rebooted my laptop. -_- It was the CTS preventing it from VE learns. When the fans turned on, it started. Have to bring the dog to vets, then Ill try to post...

I traded a 71 Camaro for this car when I was in Iraq. My twin was cursing me because the wiring was a train wreck. Probably took a few years off his life stressing :D I've tried doing BLM VE Learns at idle. Never seems to make any corrections....I'm going out to mess more with the IAC and...

https://www.dropbox.com/s/8p312r7g1zpcilq/10.dat?dl=0 Adjusted them. After holding RPMs higher than idle for a few moments the counts went back down to 16. Ill mess with them more tomorrow. For some reason I really suck at adjusting the IAC.

https://www.dropbox.com/s/e7eul2teoj3bijo/EBL_F_SFI6ClosedLoop_00002.bin?dl=0 https://www.dropbox.com/s/xmjuufdxydxxpcm/First.dat?dl=0 I'm back :) I was stupid when I wired it up, and had Injector 5 where it shouldn't go... Moved IAT to Plenum and rewired the MAPs. Idles awesome now. But my...

Ouch. Good luck!

Yep. Just ordered some new 2 and 4 wire cables, some new ECM pins from Rbob that I should've ordered more of in the first place, and some fancy connectors. Going to rewire all the crap that looks shady. Then I'll be back to bug you guys with my stupidity over ECMs :D

Alrighty, tomorrow I'll try to see if I have any fuel leaks. And rearrange the wiring and double check everything I repinned. Its probably something simple but this week I only have one day off, so I'm flying all over the place. Slow is smooth and smooth is fast. If my inmates don't stress me...

For some reason that Map Lo 34 malf came back. It's still reading voltage on the WUD O.o I have to work in a few hours, tomorrow I'm going to tidy up all the wiring, recheck everything, and start over again. Wiring gremlins suck. I put the adjustable regulator on it, set it to 43.5 line off...

Also...TPS voltage. It was set a little high, I set it back to .42.