Search results

I think I have a grounding problem with the O2 sensor..I have a one wire setup currently..Who sells a setup that has a seperate wire for grounding???Thanks,Todd

I have the scanmaster located under the radio,and above the tray console.I have tried silicone and hot wax.Both have lasted for a few days,before letting loose.I have cleaned the vinyl with alcohol..Any suggestions/comments.:confused: Todd

What sensors take over once close loop occurs???I am having a sputtering/stumbling problem as soon as the loop closes(160 degrees).. The car runs great till then...Thanks,Todd

Once the car goes into closed loop at 160 degrees,she bucks,pops,etc.:mad: ...She runs super in open loop:D ..We have ruled out cam sensor (used Caspers tool to verify)..Any suggestions....Thanks,Todd

I have been having problems lately getting my GN to track straight..Sometimes it will pull hard to the right and other times hard to the right:confused: ...Sometimes I can let go of the wheel and it tracks straight:biggrin: ... I doesn't apear that the previous owners did any front end work Any...

The car came with an electronic Autometer fuel pressure guage mounted in the dash.My buddy Ed and I disconnected it, and placed a manual(non electronic) guage he had...for a more accurate reading at the fuel rail...My question is,can I hook up both guages? I would like to see the fuel pressure...

I am looking for a stay down license plate holder...Send p.m. if you have one available with pricing...Thanks,Todd

The car runs good,until the engine temp. gets up to about 160 or so...It then starts to sputter and miss at low rpm...I removed the cam sensor cap,while the car was running..and it still sputtered/missed.I checked the crank sensor,and readjusted the tolerance.I see other members are experiencing...

I have a leaking fuel line on the passenger side.I think its the fuel return line? It has been rubbing on the TA headers..I noticed fuel dripping under the car,then I could smelll it. It has rubbed a small pinhole in the line,and is dripping fuel on the header.....:eek: :eek: Lucky the car...

I am looking to swap to roller rockers.The current non roller setup has a cracked shaft on one side.I have a roller cam and lifters currently.. Help with a brand/vendor and ratio would be appreciated...Thanks,Todd:D

I have been having a rattling noise coming from the PTE stock location stretched intercooler shroud. The thin metal vibrates quite a bit at low rpms... The last fix,I lined the top and bottom,of the shroud with rubber door edge moulding... I did an engine rebuild,and put the car back together a...

I am looking for a sway bar and lower control arms. Possibly Metco,UMI,etc. They can be new or in very good used condition, with all hardware. PM me with any information...Thanks,Todd

Can anyone give me a few suggestions,on where oil in the turbo is coming from????... It doesnt seem to coat the entire inner housing tube, but there is still residue... Thanks in advance for your input.....Todd:D

My stock exhaust manifolds are showing signs of the welds cracking at a few locations. I have heard that the TA headers are a good choice. Can I get some input from users of the headers,performance gains,etc.........:cool: Thanks,Todd

I am looking for a new drop in radiator for the car, with the engine and trans. cooler..... It is a three core unit...Any guys out there have purchased a new radiator lately??? If so,what brand, and how is it performing....I have not ruled out aluminum as of yet,but am still leaning to original...

To start, I am the fifth owner of my 87GN.... The previous owner has done extensive mods. to the car, not to include the suspension... He said that was next on his list.. The car is making 450 rear wheel h.p. as shown on the dyno sheet he provided, and 550 at the fly wheel. I have since changed...

Last Sunday my buddy and I took our GN's to the local track.. That was the first time for me and the car.. To make a long story short,the car dynoed at 540 rear wheel h.p. before Ed and I changed the stock intercooler (went with stock mount Precision stretch). We also changed the injectors to...

My current steering wheel is peeling, and becoming sticky. Does anyone know a source or sources to get a new/reconditioned replacement steering wheel? :confused:

I can't figure out how to change the inner parking lamp bulb... The outer bulb can be accessed from behind the lamp.The inner bulb is behind the front bumper support. I removed the two torx screws holding the metal lense cover on. I tried to pry the lens off, but it would not budge. Anyone knows...