Search results

Looking for an original GM filler neck from a bad tank. Must be in good shape. It has to be from a Regal tank. This is for a fuel tank research project I am working on.

Looking for an undamaged one. Preferably unrusted. Would like it cut off as close to the tank as possible. Again, Must be from an original GM tank from an 81-87 Regal tank. This is for an experiment/comparison. Thanks!

Looking for an original Terry Houston made downpipe. Must be 3 inch Stainless Integral wastegate Tight radius for stock headers Good to excellent condition. I am not interested in any other brand/manufacturers down pipes that are similar in design. Thanks as always!

I really like the GNX look buy hated the look from the rear of how far in the GTA front offset rims sat. I remember guys using the 2 piece style rims and having a wheel shop cut the center out and reattaching in a different spot to change the offset/back spacing. I am curious if anyone knows...

I have been putting the car back together after being apart for many years. Engine is fresh......109 block, Champion irons, 206/206 roller, 60lb injectors, Translator with new plastic style GM 3.5 mass air sensor, Turbo Tweak chip, Racetronix 340 pump, adjustable regulator. Scanmaster to read...

Over the years I have seen posts of adjusting the cam sensor to make starting easier especially with aftermarket camshafts. A local long time friend rotates it clock wise a little at a time until it's on the edge of not starting. He backs it up slightly from that point anr locks it down. Is...

I am putting my car back together and have a leak at the driver side header collector. The ball portion is no longer round and causing a large exhaust leak. Is there a way to repair this?

As stated. Looking for a test pipe for a stock down pipe. Prefer something nice. Thanks!

This was put on the car but I never ran the engine with it. Some light scratches in.the pipe but it's other wise new. $75 plus shipping.

Really nice ATR 3" stainless down pipe for integral wastegate. This appears to be the one to have if you have ATR headers as it is kicked out to clear the header. See picture. $400 plus shipping.

I am looking for the molded rubber insulator that went between the cooler lines and the right side radiator tank. Anyone have a nice one they would part with?

I have been accumulating parts to put my original engine back together. Unfortunately the cylinders have nice ridges at the top. As such, it looks like it will need to be bored. I am looking for a set of pistons that could be considered a good replacement for stock. Keep in mind this will be an...

I have several Buick V6 flex plates from different engines I have had over the years. For the life of me, I can't remember which engines they came off of. I had several Turbo engines and several non turbo. GM lists 2 different part numbers in the parts book; 25512348 for the non turbo and...

I am looking to buy a spare coil pack and module to have on hand. My preference is original GM but AC Delco is also fine. I have been looking and seeing differing packages with Made in USA, Made in Mexico and Made in China. I did notice that the potting material on the older modules was like a...

Looking for the OEM original sensor that has the AC logo. Looking for one that works and has no cosmetic damage. I am not interested in the later AC replacements.

Looking for a complete set up from a 2 wheel drive Blazer or Jimmy

I have been putting my 87 back together. In talking with people on Facebook I have found people talking about the baffles. There are those that talk about how bad the replacements are but do not have any data logs showing dips in fuel pressure or leaning out because of in adequacies. My original...

I need both brackets that bolt to the hood that the hood struts attach to. Anyone have any?

Used steel BHJ for stock Balance Buick V6. Has trigger wheel. Needs to be honed to fit crank as bore is small. Has a lip where some one tried to install it and it would not go on. Leading edge of key way is wide. The rest of the key way is perfect. I am open to reasonable offers. New is $651...

I bought these off of here back in 2002-2003 time period. They have sat in my attic and I realize that I will never use them. They are in good shape. Not cut off or crushed. It had hangers that had been cut and ground off that you would have to look hard to see. They could use a polishing...