Search results

Looks nice Chris. How are the doors? Any bubbling? Maybe i'll go back to the dark side soon :-P

Holyyyy ****! Thats horrible! Get well soon Scott!

Ok, low speed fan operation: Low speed fan is controlled by a) ECM according to coolent temp via the sensor in front of the intake, pointing forward, with the black and yellow wires. Fan on temp is a parameter set in the chip. b) low speed fan is also commanded on by the AC high pressure...

If I had the disposable income it would be in my garage. Beautiful car. reminds me of mine. :snif: Good luck!

Sorry to hear it Sean. but I know how you feel. One word of advice. I too have 2 kids and enjoy my time with them, but, after this summer, selling my car was a huge mistake. Sure it got me a little out of the hole, and I love my tahoe, but I miss taking it out for a romp. Maybe yours wont go and...

Notice the downpipe, clamps and fuel fittings are all the same goldish color. I suspect they are in fact coated.

The stainless used on the headers and downpipes wont remain shiny long when subjected to BOOSTED exhaust temps. It will tarnish and begin showing the "veins" in the stainless. You should reconsider coating them if you want them to look good long term

The diode trio isnt connected in any way to the plug. Its connected to the output wire bolted to the rear of the alt. The alternator by design generates an AC voltage. The diode trio is designed to snip off the sine waves that go below 0 volts, leaving only the sine waves above 0 volts. The...

Yes, technically you can, but you'll introduce a lot of moisture to the accumulator. You be better off using Nitrogen. If you must use shop air you'll need to evacuate it longer to remove the moisture. If the dessicant in the accumulator is already saturated, you may wind up sending it over the...

AC Delco 15-20225, Four Seasons 68225. Both are new not reman. I dont have good luck with reman compressors. 3 in 5 failure rate. Maybe its my supplier.

Leaking injector(s) or regulator

Lift the carpet on the left side of the trunk and check the ground. Still sounds like a ground problem, although the turn signal not working right seems weird. There is no connection that I know of between turn signals and park/instrument lights, other than bulbs and their connections. The turn...

Not true. I was in a car show with one. Forget the details but the guy proved it with all his paperwork. Until then I was unaware they even had an 83 corvette

Sounds like a bad lamp socket/ground issue still. Take each bulb out of its lens, and put the turn signal(s) on, and with a voltmeter or test light, touch the base of the bulb while in its socket and operating (the copper part). The one that causes your test light to light, or the one that shows...

Did you tap into that 2 wire plug behind the radio? Going from memory the older GM's had a orange and a black or maybe gray in a two wire plug behind the radio. One wire was memory and the other illumination. Maybe you tied the a ground into one of those wires, which wasnt in fact a ground, but...

Ta49 works well with 2800 stall. 3000 stall would be nice too but might be too loose on the road. I am a fan of precision vigilante converters. They flash nice but arent really "loose". The 3600 i had in my old car (:snif:) drove a *little* looser than stock but flashed nice when you cracked the...

Does the service engine soon light come on at key on? I wonder if you disrupted a poor connection in the orange wire by the battery.

Btw. Fast install/uninstall and injector swap are not really wiring invasive so i doubt either of those are causing your issue.

I dont know how the powerlogger is wired, or the alky setup. But i would disconnect each one one at a time. It sounds like there is a wire, maybe used for lighting, thats in the wrong circuit and backfeeding the park lights circuit. Once you unplug a devuce and the park lights go out...

Three angle valve job, cleanup and port match is my suggestion on the inexpensive side. 5 angle i understand doesnt give enough surface area to cool the face for a driver. Thats my opinion anyway. Large valve are a waste on a stock bore as the valves are shrouded by the cyl wall. I mean youll...