Search results

  1. C

    Scary low O2 #'s at WOT

    Thanks, I'll try that. But I think first switch to the colder plugs again. Again, any thoughts on 43's vs. 42's? I haven't raced the car in years, and if it makes a difference I an in colorado at 5300 feet.....less air to mix with fuel!
  3. C

    Scary low O2 #'s at WOT

    Yes, if you remove the plug and play harness, you will find the proper connectors to replace the stock one with out cutting any wires. Check out the casper electronics page , it has a diagram on a pdf which I printed up , it was quite helpful. The only extra wire I found in the conduit was...
  4. C

    Scary low O2 #'s at WOT

    The TT street chip is set for 16-18 psi, but I turn it down to 15 usually for street use. (especially if I see retard......) But it would be nice to use a bit more. And I did put the regular O2 sensor in ........what a difference!!!!! Stable O2 readings up at ~800, where before I could not...
  5. C

    Scary low O2 #'s at WOT

    Thanks guys. Jimmymack87, sorry, I thought you were referring to injectors, but I see you meant the plugs. That is why I asked "why"? Duh..... T-type 6, I understand and agree with you that the o2 is not the sole culprit. I have had this car long enough to know heat and octane are a...
  6. C

    Scary low O2 #'s at WOT

    Why?
  7. C

    Scary low O2 #'s at WOT

    Thanks.....and final question. The 4 wire heated has been in so long ......how do I switch back to the stock wiring? Do I simply remove the Casper "plug and play" wiring and what I need is still there?
  8. C

    Foreign Made Parts-What Works & What Doesn't?

    I can relate, if you look at my thread about the Denso heated O2 sensors I recently purchased. The first one crapped out in a few months. I wouldn't be surprised if I go check the label and it says "made in china".......
  9. C

    Foreign Made Parts-What Works & What Doesn't?

  10. C

    Scary low O2 #'s at WOT

    Let me first state for clarity that the very low O2 #'s I mentioned are when I push both buttons on the scanmaster to get the lowest O2 with the MPH. I have a FP gauge on the hood, it is reading the steady 1 psi increase per lb of boost as it should. Not using any coolant...... The...
  11. C

    Scary low O2 #'s at WOT

    Anyone else had problems with Denso heated O2 sensors? I bought three for a "good deal", the first on fried out after 3 months, and now I am getting 3-4 degrees of retard on shifts with audible knock. When I push recall on the scanmaster the low O2 reading is like 10-50.......that cannot be...
  12. C

    Where to get heated O2 sensor

    There are no numbers on the sensor. Casper Electronics page says it is a Denso 4 wire, but can anyone give me a code or confirmation that you can get these at a local auto part store? "from a mustang or something" really does not help!
  13. C

    Where to get heated O2 sensor

    I'm quite sure my O2 sensor is shot......All low #'s on the scanmaster and cross-counts stuck on 200!?! Many vendors have the whole kit with the wiring, but does anyone sell just the sensor ?
  14. C

    Low o2 values at WOT (tired fuel pump?)

    Yes, I have a fuel pressure gauge under the wiper which I also have been watching.... Any opinion on which is a good pump for this combo? Racetronix? Armstrong?
  15. C

    Low o2 values at WOT (tired fuel pump?)

    Hey all, I am seeing dangerously low O2 numbers on the Scanmaster at WOT, (750, and even 600's!:eek:) sometimes decreasing as I watch . I have tried to compensate by turning up the fuel pressure, does not seem to help. The fuel pump is a very old walbro 307, maybe not even strong enough...
  16. C

    rjc boost control assembly help?

    Thanks!!!
  17. C

    rjc boost control assembly help?

    I just received in my RJC boost controller. I unscrewed it to check it out and the spring and ball bearing popped out and landed on the floor. Can someone tell me which sides the spring and ball bearing should be on? As of now I have the spring in the shorter side with the adjustment...
  18. C

    new ramcharger fan question

    Hey all, My old dual ramcharger fans are about to throw one of the blades, and I am hoping to make this easy by getting the same one from gbody parts. Question is it is offered with an adapter which I am not sure I need, considering the whole thing is already installed. Sounds like (duh) a...
  19. C

    dual a-pillar 2 5/8" pod?

    Thanks for the info, Joe! As for your reply, dabigguy, safety is always a legitimate concern, but that was not the question!!??? Perhaps the national debt could be assisted if we donated one dollar for every unrelated response on TurboBuick.com! LOL CHRIS
  20. C

    dual a-pillar 2 5/8" pod?

    Yes, we do, and I have the scanmaster and all that stuff on the left side up there. Not bustin yours either, and I'm sure your setup is adavnced enough to protect your motor, but I like to see data as I drive. How will that data in your driveway help you if someting went badly sour...
  21. C

    dual a-pillar 2 5/8" pod?

    Hey all Anyone know where to get a dual a-pillar gauge pod which holds larger 2 5/8 " gauges? Poston has them but they are shut down due to a family emergency. All other sources I have checked have only the 2 1/16" size. Thanks, Chris
Top