Search results

  1. Y

    getting idle for MAF translator

    87 GN daily driver has tt chip and injectors., have been driving the car for the past few months, runs out good , just doesnt want to idle. Have a 3.5" MAF sensor connected to a 3" intake setup. This car will not idle, and I have replaced and checked all vacuum lines. Adjustable fuel pressure...
  3. Y

    any suggestions installing a new turn signal switch?

    this is the circular plastic piece with the wires that is one unit and has a harnes connector on the end of it. The wire length is about 18 inches. does the steering whee come off to install? thankx!
  4. Y

    what is a good part # for a turn signal switch and also a windshield wiper motor?

    just seeking a decent source, not wanting a $400 turn signal switch, or a $700 windshield wiper motor. Thankx!!!!!!
  5. Y

    IAC at 90 and screw out all the way

    So this is a daily driver with a 3.5" MAF and a 3" intake tube all the way to the turbo. Has MAF translator and scangage. My settings are rich at idle and plus 14 % rich at WOT. car likes to stall when downshifting to an idle setting. with the IAC adjust screw unthreaded out, the throttle...
  6. Y

    ngk UR5 2771 wont thread into hole

    Imma trying to install these and I notice the shoulder is shorter and different. Has anyone had the same pleasure im having trying to install these?
  7. Y

    what size shims should I order for comp cams 980 ?

    this is a daily driver and has stock internals. Ive done valve springs before on a diesel engine. With the same spring actually. Anyway , I dont know the height that is best, nor the shim sizes to order, thankx!!!!!
  8. Y

    what is best # for the IAC? i have scangauge and keeps stalling

    daily driver, already set the TPS , and checked vacuum lines. do have delete on the exhaust back pressure valve on drivers side bank. I have a MAF translator and pretty much run close to 128 blm at WOT and idles decently a little rich. thanks for the wisdom, Ronjon
  9. Y

    what is the beast brand of IAC to buy?

    th end just fell out of mine, its time to order me one. Im inclined to buy delco , any brand better to recommend? thankx, ROnjon
  10. Y

    have 4 ways flashing, no right turn signals .

    this is also on the dash. there is nothing that illuminates when the right hand turn selector is activated. considering and new turn signal selcetor switch. been like this the past few months. Any fuses related to this circuit? thankx.......
  11. Y

    who makes the piece that fits in the high beam headlight as an air intake inlet?

    so as to remove the headlight high beams and have the plastic insert where the headlight was. this would allow air to flow into engine bay. not sure of the name of it, thanks, Ronjon
  12. Y

    looking for a 3 inch downpipe for a daily driver GN

    let me know what you have, my email rjnjr11@yahoo.com live in Florida, thanks
  13. Y

    just installed MAF translator, what parameters should I strive for on scangauge ?

    87 GN daily driver, newest version translator , TT 5.7 chip, 3 1/2 MAF , Scangauge G. Have dips set On, On , On , Off. Base set at 3 1/2 MAF, lean at idle. WOT I've been playing with to be near 128 BLM. Havent completely dialed the WOT settings and it cuts out as soon as I put it in reverse ...
  14. Y

    how is the rear upper seat removed?

    Im researching on this so I can redo the upholstery of the rear seat. I'd like to completely remove this a s one piece. Thanks, Ronjon
  15. Y

    Where do I begin? turn key, no power at all.

    battery is charged, all fuses under dash intact. 1st it did this is iast night at 5pm. I waited about 15 minutes , disconnected battery and reconnected it and it starterd and drove perfectly for 45 minutes. same exact thing just happened 10 minutes ago. Newer ignition module and coil pack (...
  16. Y

    might need ecm , need a part number

    87 BGN, have a pcm now ,the id tagis missing the info , i would like to get another. Heard something about the last 3 numbers are 141? anyway, I have an issue when car shuts down after running about a half hour. Only on cold starts in the mornings. Dunno, thanks for the help
  17. Y

    updated timing cover ?

    im about to replace the original factory timing chain and gears, and wondering while the timing cover is off should I replace the timing cover with a newer version? or even consider a cam? everything is original and this is a daily driver, although going to a double roller style. thanks.
  18. Y

    would like to change atf in the t/c

    i havent crawled under my 87 GN, and on here to learn about the proces of changing the ATF . this is an original car so wondering if there are trans cooler lines also if theres a drain plug on the t/c. thanks
  19. Y

    valve spring tool wanted to use

    Im only planning on doing this once seems silly to spend $50plus on the valve spring tool for comp cam springs install. I'd be happy to pay shipping both ways if anyone has one of these available. Thanks
  20. Y

    where to get a spring removal tool?

    just got my comp cam 910 springs and seeking a source for the tool to change the factory ones out. Where can I get the tool for a realistic price? any insight to the installation while im on the topic? thanks everyone
  21. Y

    where to get a new cat hanger bracket

    rubber in my catalytic converter hangar bracket has dry rotted, any souorce for just the rubber or a brand new bracket? thankx
Top