Search results

Does it have the inlet bell bolted on? Where can I send a money order to? Thank's, Dan

Hi, I am looking for a stock compressor side (aluminum),for the 86-87 garrett turbo found on the G.N. Thank's, Dan

Misplaced stock turbo inlet bell.Anyone have a spare?Would consider compressor with bell. Thank's,Dan

I am trying to compare turbos,so I can upgrade.Does anyone know the specs for the 87 gn garrett turbo? I would like to find out the A/R for the compressor and the turbine,also would like to know the wheel sizes and the trim. Thanks

I want to upgrade my 87 t, using a t-3 flange turbo. I'm a little confused about how to compare turbos with the stock Garrett unit. When a/r is referred to, are they talking about the turbine, or the compressor? What does "trim" mean? Any suggested t-3 flange turbos for a stock, rebuilt 3.8...

Hi, I am looking to upgrade a stock 87 gn. It seems to me the t3 flange turbos are a lot cheaper. I am trying to compare some of these to the stock Garrett, but am getting very confused. For a stock 3.8, what t-3 flange turbo would you reccomend? I know I will have to change the downpipe,but...

code 12 Thanks for the reply, you're right it's nothing to worry about. After reading up on it, I remember when I first tried to start the car, I cranked the engine over without the big white plug connected, under the module. That is how it set the code 12, no tach signal. My mistake, sorry to...

temp light on Did you check the coolant temp sensor ? Check the one with the single wire on the front of the intake. The one by the fuel pressure regulator turns the fan on. Hope this helps ,Dan

Reassembling 87 t-type after rebuild. I have a trouble code # 12, tach is pegged . Book says no tach signal. Anyone ever seen this? What to do? T%hank's, Dan

Thanks for the reply, do you know where I can find the cam sensor setting procedure? I seemm to recall one where you used a test light. Ever hear of it? Thank's Dan

I just had my bottom end re-done and am now re-installing engine,in my 87 t.I had no idea you have to index the oil pump shaft. Can someone explain how this is done? Also, I have the Cassen's cam sensor tool,but,no directions.Would someone explain how to set the cam sensor,either with or without...

You mentioned an adaptor to go from 3 bolt to 4.Do you know where to get one? Thanks, Dan

I need a t-top roof,or the body shell. jarheadcmchnj@yahoo.com

Jeff, I spoke to you on the phone on monday,about cutting the t-top roof off of your car.You can reach me at: jarheadcmchnj@yahoo.com or: 609 364 4380. Thank's, Dan

would you have the t-top roof from one of these cars ? i don;t need the glass panels,but the metal roof from a pillars back.how much? jarheadcmchnj@yahoo.com

Thanks for the reply,I am a newbie to this site,may I ask"Who is Chris McDade,and how do I contact him?" Thanks, Dan

hi,i spun a rod bearing,and ruined the end cap,rod looks good,anyone know where to get one,or does any one have an 86 109 rod they would like to sell?thanks, dan

Anyone know if you can use an 86 monte ss trans and/or converter in an 86 gn?

i am an idiot i had an inspiration,i shifted the gears manually;the trans is shifting into 4th,but the 1-2 and 2-3 are so close ,you can't feel 2 shifts,only one.i will move the tv cable to spread them out. i think the speedo gear is wrong for this trans.i believe i am going faster than what is...

confused i have the original trans.and converter.during the time i was trying to figure out this problem,my original trans started to slip in the 1-2 shift and while backing.i swapped the trans for one i bought for my 87 t,a couple of years ago.i took that trans back out because i did not like...