Search results

Anyone know of a good place to take the GN to get dynotuned in the central jersey area. Willing to travel some

Was there a water issue right after filling up your tank? A lot of people do not know that the Ethanol blended fuel has a 90day shelf life. It will start separating and becoming water. So if the gas station is not a high volume then there can be an issue of water in the fuel tank or if your...

Thanks for the info. Yea I would spend $300 on the stock ones then another few yrs down the road have to buy them again. Also this is not a daily driver and I will be putting classic car plates on it and will be limited to $3k miles a year so driving quality is not a big issue.

I am not sure if this is the right place for the answer, but I am in the midst of repainting my GN and may actually do a body off resto. I would like to know if anyone has replaced the body bushings and what brand they used or who they bought them from. Any suggestions would be a great help.

I am in need of new rear springs. The car is basically a weekend street car with limited track use. I do have airbags, but the springs are shot. What is a good brand to go with and should I get lowering springs??? I might as well do all the corners also. What about bushings? I am trying to...

http://josh.swoca.net/antiricer.wmv I don't know if this video has been poster before

im talking about updated models.

I have read over the boards about both and gone to the T-Link website, but still am not sure what is the best tuning tool. I have a scanmaster right now, but would like to save the information that is being recorded. I se T-link is always being upgraded, how often is data in the DS being...

I have a 3.5" MAF, T+ and extender chip, do i still need to run the ats?

WHich tire is wider? The BFG 28" or nitto 28" drag radials?

The new Mease 24 Row. Definetly look into it. Just had an article in GMHTP. http://www.measeperformance.com/

Who makes an extender chip. I know Bob Bailey has one does anyone else. Also how do i get in touch w/ him. Eric From Turbotweak recommended him because im upgrading the the T+ from stock MAF. So if anyone is looking for a TurboTweak chip for 009's and alky i have one.

I went w/ the 275/60's on my stock rims. Looks good but am having a lot of rub, put spacers in and didn't help much. Now im going to resort to notching the frame.

Does anyone know if the translator will work w/ the LT4 MAF sensor with the 3 prong system?

I need to replace my MAF again and no sure if I should spend the money for the stock if it is going to just die on me every year. What is recommended for the LS1/Lt1 MAF's. IS there a difference between the 2. I have seen 3" and 3.5" which is better to go with. Where can I buy a stock MAF so...

I need my frame notched and was wondering if anyone in New Jersey knows how to do it or can do it for me. Even Pennsylvania will be fine like the philly area.

I have airbags, i even pumped them up a little more just for that extra support. With no spacers the left side rubbed the fram right side slight rubbed the frame. Left you can see where it hit in 3 spots.

stock rims, 3/8"spacers, stock backspacing not sure on the psi, what is recommended?

I installed a set of BFG 275/60/R15 DR's last friday and have nothing but problems with them rubbing somewhere. I installed spacers bc they rubbed the frame on the one side now i notice i got a gash in the right side tire on the outside from a sharp edge on the wheel well. The left side seems...

I am getting and error code 45. When I got the code the first thing i did was turn the fuel pressure down, I am only running 41#line off. That didn't work so i changed the 02 sensor disconnected the ecm for a little bit then hooked it back up. Turned the car back on and same code. My MAF...